Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)

DTC    B1441    Air Mix Damper Control Servo Motor Circuit (Passenger Side)

for Preparation Click here


DESCRIPTION

The damper servo sub-assembly (air mix damper servo) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air mix damper to any position. As a result, the air mix damper varies the mixture of hot air from the heater core and cold air from the evaporator so that the temperature of the air is as requested.

HINT:
Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.


DTC Code
DTC Detection Condition
Trouble Area
B1441
The air mix damper position does not change when the air conditioning amplifier assembly operates the damper servo sub-assembly (air mix damper servo).
  1. Damper servo sub-assembly (air mix damper servo)
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM


E180810E37


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (AIR MIX DAMPER SERVO)
  1. Use the Data List to check if the damper servo sub-assembly (air mix damper servo) is functioning properly (Click here).

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Mix Servo Targ Pulse (D)
    Damper servo sub-assembly (air mix damper servo) target pulse / Min.: 0, Max.: 255
    112 or 127 (pulse): MAX COOL
    21 or 31 (pulse): MAX HOT
    -
    Air Mix Servo Actual Pulse (D)
    Damper servo sub-assembly (air mix damper servo) actual pulse / Min.: 0, Max.: 255
    112 or 127 (pulse): MAX COOL
    21 or 31 (pulse): MAX HOT
    -

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to problem symptoms table)
    A
    OK (When troubleshooting according to the DTC)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.PERFORM ACTIVE TEST USING TECHSTREAM (AIR MIX DAMPER SERVO)
  1. Select the Active Test, use the Techstream to generate a control command, and then check that the damper servo sub-assembly (air mix damper servo) operates (Click here).

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Air Mix Servo Targ Pulse (D)
    Damper servo sub-assembly (air mix damper servo) pulse
    Min.: 0, Max.: 255
    -

    OK:
    Damper servo sub-assembly (air mix damper servo) operates normally.



NG
Go to step 3
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

3.REPLACE DAMPER SERVO SUB-ASSEMBLY (AIR MIX DAMPER SERVO)
  1. Replace the damper servo sub-assembly (air mix damper servo) (Click here).

    HINT:
    Since the damper servo sub-assembly (air mix damper servo) cannot be inspected while it is removed from the vehicle, replace the damper servo sub-assembly (air mix damper servo) with a new or normally functioning one.


NEXT


4.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1441 is not output.



NG
Go to step 5
OK

END (DAMPER SERVO SUB-ASSEMBLY [AIR MIX DAMPER SERVO] IS FAULTY) 

5.REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
  1. Temporarily replace the air conditioning amplifier assembly with a new or normally functioning one (Click here).


NEXT


6.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1441 is not output.



NG
REPLACE AIR CONDITIONING HARNESS ASSEMBLY (Click here)
OK

END (AIR CONDITIONING AMPLIFIER ASSEMBLY IS FAULTY)