Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)

DTC    B1442    Air Inlet Damper Control Servo Motor Circuit

for Preparation Click here


DESCRIPTION

The recirculation damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air inlet damper to any position, which controls the intake air settings (fresh, fresh/recirculation and recirculation).

HINT:
Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.


DTC Code
DTC Detection Condition
Trouble Area
B1442
The air inlet damper position does not change when the air conditioning amplifier assembly operates the recirculation damper servo sub-assembly.
  1. Recirculation damper servo sub-assembly
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM


E180810E26


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (RECIRCULATION DAMPER SERVO)
  1. Use the Data List to check if the recirculation damper servo sub-assembly is functioning properly (Click here).

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Inlet Damper Targ Pulse
    Recirculation damper servo sub-assembly target pulse / Min.: 0, Max.: 255
    7 (pulse): Recirculation
    28 (pulse): Fresh
    -
    Air Inlet Damper Actual Pulse
    Recirculation damper servo sub-assembly actual pulse / Min.: 0, Max.: 255
    7 (pulse): Recirculation
    28 (pulse): Fresh
    -

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to problem symptoms table)
    A
    OK (When troubleshooting according to the DTC)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.PERFORM ACTIVE TEST USING TECHSTREAM (RECIRCULATION DAMPER SERVO)
  1. Select the Active Test, use the Techstream to generate a control command, and then check that the recirculation damper servo sub-assembly operates (Click here).

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Air Inlet Damper Targ Pulse
    Recirculation damper servo sub-assembly target pulse
    Min.: 0, Max.: 255
    -

    OK:
    Recirculation damper servo sub-assembly operates normally.



NG
Go to step 3
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

3.REPLACE RECIRCULATION DAMPER SERVO SUB-ASSEMBLY
  1. Replace the recirculation damper servo sub-assembly (Click here).

    HINT:
    Since the recirculation damper servo sub-assembly cannot be inspected while it is removed from the vehicle, replace the recirculation damper servo sub-assembly with a new or normally functioning one.


NEXT


4.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1442 is not output.



NG
Go to step 5
OK

END (RECIRCULATION DAMPER SERVO SUB-ASSEMBLY IS FAULTY) 

5.REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
  1. Temporarily replace the air conditioning amplifier assembly with a new or normally functioning one (Click here).


NEXT


6.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1442 is not output.



NG
REPLACE AIR CONDITIONING HARNESS ASSEMBLY (Click here)
OK

END (AIR CONDITIONING AMPLIFIER ASSEMBLY IS FAULTY)