Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Microphone Circuit between Microphone and Radio Receiver

for Preparation Click here


DESCRIPTION

  1. The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
  2. Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM


E227677E61


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the G49 radio and display receiver assembly connector.

  1. Disconnect the U2 map light assembly (telephone microphone assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G49-4 (MACC) - U2-14 (MACC)
    Always
    Below 1 Ω
    G49-5 (MIN+) - U2-13 (MCO+)
    Always
    Below 1 Ω
    G49-6 (SNS2) - U2-15 (SNS2)
    Always
    Below 1 Ω
    G49-19 (MIN-) - U2-12 (MCO-)
    Always
    Below 1 Ω
    G49-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    G49-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    G49-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    G49-18 (SGND) - Body ground
    Always
    10 kΩ or higher
    G49-19 (MIN-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
  1. Reconnect the G49 radio and display receiver assembly connector.

  1. Reconnect the U2 map light assembly (telephone microphone assembly) connector.



    E280737E05
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G49-4 (MACC) - Body ground
    Ignition switch ACC
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G49-18 (SGND) - Body ground
    Always
    Below 1 Ω
    G49-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Disconnect the U2 map light assembly (telephone microphone assembly) connector.



    E187117E57
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U2-15 (SNS2) - U2-12 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Map Light Assembly (Telephone Microphone Assembly))



NG
Go to step 5
OK


4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Reconnect the G49 radio and display receiver assembly connector.

  1. Reconnect the U2 map light assembly (telephone microphone assembly) connector.

  1. Turn the ignition switch to ACC.



    E187122E44
  1. Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the U2 map light assembly (telephone microphone assembly) connector.
    Text in Illustration 
    *a
    Component with harness connected
    (Map Light Assembly (Telephone Microphone Assembly))

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.

    Result:
    Result
    Proceed to
    A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output
    A
    A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output
    B



B
Go to step 5
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly (Click here).

  1. Check if the same malfunction recurs.

    Result:
    Result
    Proceed to
    Malfunction does not recur
    (returns to normal)
    A
    Malfunction recurs
    B



B
REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)