DTC B1656/38 Seat Belt Buckle Switch LH Circuit Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1656/38 | One of the following conditions is met:
|
|

| 1.CHECK FOR DTC |
Turn the ignition switch to ON.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and front seat inner belt LH.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and front seat inner belt LH.
![]() |
Check that the connectors (on the center airbag sensor side and front seat inner belt LH side) are not damaged.
| *1 | Front Seat Inner Belt LH |
| *2 | Center Airbag Sensor |
|
| ||||
| OK | |
| 4.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

| *1 | Front Seat Inner Belt LH | *2 | Center Airbag Sensor |
| *3 | No. 2 Floor Wire | *4 | Connector C |
| *5 | Connector B | - | - |
| *a | Front view of wire harness connector (to Front Seat Inner Belt LH) | *b | Rear view of wire harness connector (to Center Airbag Sensor) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O3-2 (LBE+) - Body ground | Ignition switch ON | Below 1 V |
| O3-1 (LBE-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O3-2 (LBE+) - O1-10 (LBE+) | Always | Below 1 Ω |
| O3-2 (LBE+) - Body ground | Always | 1 MΩ or higher |
| O3-1 (LBE-) - O1-18 (LBE-) | Always | Below 1 Ω |
| O3-1 (LBE-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK FRONT SEAT INNER BELT LH (SEAT BELT BUCKLE SWITCH) |
![]() |
Connect the connectors to the center airbag sensor and front seat inner belt LH.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Front Seat Inner Belt LH |
| *2 | Center Airbag Sensor |
|
| ||||
| OK | ||
| ||
| 6.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the front seat inner belt LH (Click here).
| NEXT | |
| 7.CHECK CENTER AIRBAG SENSOR |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Front Seat Inner Belt LH |
| *2 | Center Airbag Sensor |
|
| ||||
| OK | ||
| ||