Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B2287    LIN Communication Master Malfunction

DTC    B278C    Lost Communication with Power Source Control

for Preparation Click here


DESCRIPTION

  1. DTC B2287 is stored when there is an open or short circuit or an ECU communication malfunction between the power management control ECU and certification ECU.
  2. DTC B278C is stored when LIN communication between the certification ECU and power management control ECU stops for 10 seconds or more.

DTC Code
DTC Detection Condition
Trouble Area
B2287
There is an open or short circuit or an ECU communication malfunction between the power management control ECU and certification ECU.
  1. Certification ECU
  2. Power management control ECU
  3. Harness or connector
B278C
No communication between the certification ECU and power management control ECU for 10 seconds or more.
  1. Certification ECU
  2. Power management control ECU
  3. Harness or connector

WIRING DIAGRAM


C212392E01


INSPECTION PROCEDURE

NOTICE:
  1. When using the Techstream with the ignition switch off to troubleshoot:
    Connect the Techstream to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.
  2. Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

HINT:
When DTC B2287, B278C and B2785 are output simultaneously, perform troubleshooting for DTC B2785 first (Click here).

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2287 or B278C is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the F79 certification ECU connector.

  1. Disconnect the F80 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F79-29 (LIN) - F80-24 (LIN2)
    Always
    Below 1 Ω
    F79-29 (LIN) or F80-24 (LIN2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY AND BODY GROUND)


    C198951E18
  1. Disconnect the F80 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F80-5 (GND2) - Body ground
    Always
    Below 1 Ω
    F80-6 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F80-1 (AM22) - Body ground
    Always
    11 to 14 V
    F80-2 (AM21) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*a
Rear view of wire harness connector
(to Power Management Control ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE POWER MANAGEMENT CONTROL ECU
  1. Temporarily replace the power management control ECU with a new or normally functioning one (Click here).


NEXT


6.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2287 or B278C is not output.



NG
REPLACE CERTIFICATION ECU (Click here)
OK

END (POWER MANAGEMENT CONTROL ECU IS DEFECTIVE)