Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B2321    Driver Side Door ECU Communication Stop

for Preparation Click here


DESCRIPTION

This DTC is stored when LIN communication between the front power window regulator motor assembly LH and main body ECU stops for 10 seconds or more.

DTC Code
DTC Detection Condition
Trouble Area
B2321
No communication between the front power window regulator motor assembly LH and main body ECU for 10 seconds or more.
  1. Front power window regulator motor assembly LH
  2. Main body ECU
  3. Harness or connector

WIRING DIAGRAM


C211493E12


INSPECTION PROCEDURE

NOTICE:
  1. When using the Techstream with the ignition switch off to troubleshoot:
    Connect the Techstream to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.
  2. Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

HINT:
  1. When communication between the front power window regulator motor assembly LH and main body ECU stops, DTC B2325 is also stored.
  2. When DTC B1206 and B2321 are output simultaneously, perform troubleshooting for DTC B1206 first.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2321 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR LH)
  1. Disconnect the h1 multiplex network master switch assembly connector.

  1. Disconnect the I2 front power window regulator motor assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    h1-16 (LIN2) - I2-9 (LIN)
    Always
    Below 1 Ω
    h1-16 (LIN2) or I2-9 (LIN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR LH - BATTERY AND BODY GROUND)


    C216965E01
  1. Disconnect the I2 front power window regulator motor assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I2-1 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I2-2 (B) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly LH)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
  1. Temporarily replace the front power window regulator motor assembly LH with a new or normally functioning one (Click here).


NEXT


6.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2321 is not output.



NG
REPLACE MAIN BODY ECU (Click here)
OK

END (FRONT POWER WINDOW REGULATOR MOTOR LH IS DEFECTIVE)