Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B2322    Front Passenger Side Door ECU Communication Stop

for Preparation Click here


DESCRIPTION

This DTC is stored when LIN communication between the front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC Code
DTC Detection Condition
Trouble Area
B2322
No communication between the front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) for 10 seconds or more.
  1. Front power window regulator motor assembly RH
  2. Main body ECU (multiplex network body ECU)
  3. Harness or connector

WIRING DIAGRAM


C211493E13


INSPECTION PROCEDURE

NOTICE:
  1. When using the Techstream with the ignition switch off to troubleshoot:
    Connect the Techstream to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.
  2. Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

HINT:
When communication between the front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2322 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR RH)
  1. Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (Click here).

  1. Disconnect the H2 front power window regulator motor assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-16 (LIN2) - H2-9 (LIN)
    Always
    Below 1 Ω
    A-16 (LIN2) or H2-9 (LIN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR RH - BATTERY AND BODY GROUND)


    C216965E02
  1. Disconnect the H2 front power window regulator motor assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H2-1 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H2-2 (B) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly RH)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
  1. Temporarily replace the front power window regulator motor assembly RH with a new or normally functioning one (Click here).


NEXT


6.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2322 is not output.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (FRONT POWER WINDOW REGULATOR MOTOR RH IS DEFECTIVE)