Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Smart Key System)

DTC    B279A    Theft Deterrent System Communication Line High Fixation

for Preparation Click here


DESCRIPTION

If the communication line (EFIO-IMI) to the ID code box is stuck on HI output, the ECM stores this DTC.

DTC Code
DTC Detection Condition
Trouble Area
B279A
The communication line (EFIO-IMI) between the ECM and the ID code box is stuck on HI output.
  1. Harness or connector
  2. ID code box
  3. ECM

WIRING DIAGRAM


B235867E03


INSPECTION PROCEDURE

NOTICE:
  1. When the ID code box is replaced, refer to Registration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    If DTCs other than DTC B279A are output, troubleshoot those DTCs first.

    Result 
    Result
    Proceed to
    DTC B279A is not output
    A
    DTC B279A and other DTCs are output
    B
    DTC B279A is output
    C



B
Go to DIAGNOSTIC TROUBLE CODE CHART (Click here)

C
Go to step 3
A

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK HARNESS AND CONNECTOR (ID CODE BOX - ECM)
  1. Disconnect the F72 box connector.

  1. Disconnect the F50 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F72-6 (EFIO) - F50-14 (IMI)
    Always
    Below 1 Ω
    F72-6 (EFIO) or F50-14 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK ID CODE BOX (OUTPUT)


  1. Using an oscilloscope, check the waveform.


    B242189E01


    Text in Illustration 
    *a
    Component with harness connected
    (ECM)
    -
    -
    Measurement Condition 
    Item
    Content
    Tester Connection
    F50-14 (IMI) - Body ground
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Engine switch on (IG)

    OK:
    Waveform is output normally (refer to illustration).



NG
Go to step 5
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (ID CODE BOX - BATTERY AND BODY GROUND)


    E180667E03
  1. Disconnect the F72 box connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F72-1 (+B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F72-8 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to ID Code Box)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE ID CODE BOX
  1. Replace the ID code box (Click here).


NEXT


7.REGISTER RECOGNITION CODES
  1. Register the recognition codes in the ECUs (Click here).


NEXT


8.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID (Click here).


NEXT


9.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


10.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B279A is not output.



NG
REPLACE ECM (Click here)
OK

END (ID CODE BOX IS DEFECTIVE)