Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > Starter Signal Circuit

for Preparation Click here


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch*1 or terminal STAR of the power management control ECU*2 to the park/neutral position switch and also flows to terminal STA of the ECM (STA Signal).
  1. *1: w/o Smart Key System
  2. *2: w/ Smart Key System

WIRING DIAGRAM


A227112E01


A227113E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
This chart is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to Problem Symptoms Table (Click here).

1.CHECK IF VEHICLE IS EQUIPPED WITH SMART KEY SYSTEM
  1. Check if the vehicle is equipped with the smart key system.

    Result 
    Result
    Proceed to
    w/o Smart Key System
    A
    w/ Smart Key System
    B



B
Go to step 10
A


2.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value.

    OK:

    Ignition Switch Position
    Starter Signal
    ON
    Close
    START
    Open



NG
Go to step 3
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

3.CHECK STARTER RELAY (ST) (POWER SOURCE)


    A227799E01
  1. Remove the starter relay (ST) from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Starter relay (ST) terminal 1 - Body ground
    Engine cranking
    11 to 14 V

    HINT:
    The engine does not crank because the relay is not installed.

    Text in Illustration 
    *1
    Starter Relay (ST)
    *2
    Engine Room Relay Block

  1. Reinstall the starter relay (ST).



NG
Go to step 6
OK


4.INSPECT STARTER RELAY (ST)
  1. Inspect the starter relay (ST) .



NG
REPLACE STARTER RELAY (ST)
OK


5.CHECK HARNESS AND CONNECTOR (STARTER RELAY (ST) - BODY GROUND)


    A227799E01
  1. Remove the starter relay (ST) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Starter relay (ST) terminal 2 - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Starter Relay (ST)
    *2
    Engine Room Relay Block

  1. Reinstall the starter relay (ST).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY (ST) - BODY GROUND)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH) 

6.CHECK HARNESS AND CONNECTOR (STARTER RELAY (ST) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
  1. Remove the starter relay (ST) from the engine room relay block.

  1. Disconnect the park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    Starter relay (ST) terminal 1 - B42-5
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    Starter relay (ST) terminal 1 or B42-5 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the starter relay (ST).

  1. Reconnect the park/neutral position switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly for 4WD .

  1. Inspect the park/neutral position switch assembly for 2WD .



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK


8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - IGNITION SWITCH ASSEMBLY)
  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B42-4 - F15-1 (ST1)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B42-4 or F15-1 (ST1) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the park/neutral position switch assembly connector.

  1. Reconnect the ignition switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT IGNITION SWITCH ASSEMBLY
  1. Inspect the ignition switch assembly .



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY) 

10.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value.

    OK:

    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON



NG
Go to step 11
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

11.CHECK STARTER RELAY (ST) (POWER SOURCE)


    A227799E01
  1. Remove the starter relay (ST) from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Starter relay (ST) terminal 1 - Body ground
    Engine cranking
    11 to 14 V

    HINT:
    The engine does not crank because the relay is not installed.

    Text in Illustration 
    *1
    Starter Relay (ST)
    *2
    Engine Room Relay Block

  1. Reinstall the starter relay (ST).



NG
Go to step 14
OK


12.INSPECT STARTER RELAY (ST)
  1. Inspect the starter relay (ST) .



NG
REPLACE STARTER RELAY (ST)
OK


13.CHECK HARNESS AND CONNECTOR (STARTER RELAY (ST) - BODY GROUND)


    A227799E01
  1. Remove the starter relay (ST) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Starter relay (ST) terminal 2 - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Starter Relay (ST)
    *2
    Engine Room Relay Block

  1. Reinstall the starter relay (ST).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY (ST) - BODY GROUND)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH) 

14.CHECK HARNESS AND CONNECTOR (STARTER RELAY (ST) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
  1. Remove the starter relay (ST) from the engine room relay block.

  1. Disconnect the park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    Starter relay (ST) terminal 1 - B42-5
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    Starter relay (ST) terminal 1 or B42-5 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the starter relay (ST).

  1. Reconnect the park/neutral position switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly for 4WD .

  1. Inspect the park/neutral position switch assembly for 2WD .



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK


16.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B42-4 - F81-3 (STAR)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B42-4 or F81-3 (STAR) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the park/neutral position switch assembly connector.

  1. Reconnect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO SMART KEY SYSTEM (Click here)