Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Meter Illumination does not Dim at Night

for Preparation Click here


DESCRIPTION

If the dimmer switch is turned to TAIL, HEAD or AUTO, the main body ECU sends a TAIL relay signal, panel light illumination signal, panel relay signal and TAIL cancel OFF signal to the combination meter. Then the meter and accessory meter become dim.

HINT:
w/ TAIL Cancel Switch:
When the headlights are illuminated and the TAIL cancel switch is turned on, the meter does not dim.


WIRING DIAGRAM


E200254E01


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    CAN communication system DTC is not output
    A
    CAN communication system DTC is output
    B



B
Go to CAN COMMUNICATION SYSTEM (Click here)
A


2.READ VALUE USING TECHSTREAM (LIGHT CONTROL RHEOSTAT)
  1. Operate the Techstream according to the display and select the Data List (Click here).

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Tail Cancel SW*
    TAIL cancel switch condition/ON or OFF
    on: TAIL cancel switch on
    off: TAIL cancel switch off
    -
    Rheostat value
    Light control rheostat switch input/Min.: 0, Max.: 100
    Light control rheostat switch is fully turned downward (0) → fully turned upward (100)
    Unit: %

    1. *: w/ TAIL Cancel Switch

    OK:
    Light brightness can be changed within specified range by manual operation.



NG
Go to step 3
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

3.INSPECT LIGHT CONTROL RHEOSTAT
w/o TAIL Cancel Switch:


  1. Inspect the light control rheostat.


    E200224E02

    1. Remove the light control rheostat (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 (T) - 1 (E)
      Always
      8 to 12 kΩ
      3 (RV) - 1 (E)
      Light control rheostat fully turned upward → fully turned downward
      8 to 12 kΩ → Below 50 Ω

w/ TAIL Cancel Switch:


  1. Inspect the light control rheostat.


    E200225E02

    1. Remove the light control rheostat (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 (T) - 5 (TC)
      TAIL cancel switch off → on
      1 MΩ or higher → Below 1 Ω
      7 (T) - 1 (E)
      Always
      8 to 12 kΩ
      3 (RV) - 1 (E)
      Light control rheostat fully turned upward → fully turned downward
      8 to 12 kΩ → Below 50 Ω



NG
REPLACE LIGHT CONTROL RHEOSTAT (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - LIGHT CONTROL RHEOSTAT)
  1. Disconnect the F14 meter connector.

  1. Disconnect the F5 rheostat connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F14-37 (RHIG) - F5-7 (T)
    Always
    Below 1 Ω
    F14-38 (TR) - F5-3 (RV)
    F14-39 (E2) - F5-1 (E)
    F14-36 (TC) - F5-5 (TC)*

    1. *: w/ TAIL Cancel Switch



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)