Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS

WINDSHIELD GLASS > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.



3. REMOVE FRONT FENDER MAIN SEAL LH


    E198982
  1. Detach the 4 clips and 2 guides and remove the front fender main seal LH.



4. REMOVE FRONT FENDER MAIN SEAL RH

HINT:
Use the same procedure as for the LH side.



5. REMOVE FRONT FENDER TO COWL SIDE SEAL LH


    E198989
  1. Detach the 5 claws and remove the front fender to cowl side seal LH.



6. REMOVE FRONT FENDER TO COWL SIDE SEAL RH

HINT:
Use the same procedure as for the LH side.



7. REMOVE FRONT WIPER ARM HEAD CAP


    E198979E01
  1. Using a screwdriver, detach the 3 claws and remove the front wiper arm head cap.

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedure described for the LH side.

    Text in Illustration 
    *1
    Protective Tape



8. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E198980
  1. Remove the nut and the front wiper arm and blade assembly LH.



9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E198981
  1. Remove the nut and the front wiper arm and blade assembly RH.



10. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E198984E01
  1. Remove the 2 clips.

  1. Detach the 6 claws and guide (A).
    Text in Illustration 
    *1
    Guide A
    *2
    Guide B

  1. Detach the 9 guides (B) and pull out the cowl top ventilator louver sub-assembly.



11. REMOVE DOOR SCUFF PLATE ASSEMBLY LH


    B240006E01
  1. Put protective tape around the door scuff plate assembly LH.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides to remove the door scuff plate assembly LH.

    HINT:
    Tape the screwdriver tip before use.



12. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



13. REMOVE COWL SIDE TRIM BOARD LH


    B238734
  1. Remove the clip.

  1. Detach the clip and claw to remove the cowl side trim board LH.



14. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure as for the LH side.



15. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B240007
  1. Remove the front door opening trim weatherstrip LH.



16. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



17. REMOVE ASSIST GRIP PLUG


    B238813E01
  1. Using a screwdriver, detach the 2 claws to remove the assist grip plug.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedure for the other assist grip plug.



18. REMOVE NO. 1 ASSIST GRIP


    B238814
  1. Remove the 2 bolts.

  1. Detach the 2 claws to remove the No. 1 assist grip.



19. REMOVE FRONT PILLAR GARNISH RH


    B240014
  1. Detach the clip and 3 guides to remove the front pillar garnish RH.



    B240016E01
  1. Protect the curtain shield airbag assembly.

    1. Completely cover the curtain shield airbag assembly with a protective cover and secure the ends of the cover with adhesive tape as shown in the illustration.
      Text in Illustration 
      *1
      Curtain Shield Airbag Assembly
      *2
      Adhesive Tape
      *3
      Protective Cover

      NOTICE:
      Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish RH is removed.



20. REMOVE FRONT PILLAR GARNISH LH


    B353464E01
  1. Using a screwdriver, detach the 2 claws to remove the No. 1 front pillar garnish cover LH.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    B353465
  1. Remove the bolt.

  1. Detach the clip.



    B353468
  1. Detach the 2 guides to remove the front pillar garnish LH.



    B240015E01
  1. Protect the curtain shield airbag assembly.

    1. Completely cover the curtain shield airbag assembly with a protective cover and secure the ends of the cover with adhesive tape as shown in the illustration.
      Text in Illustration 
      *1
      Curtain Shield Airbag Assembly
      *2
      Adhesive Tape
      *3
      Protective Cover

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish LH is removed.



21. REMOVE ASSIST GRIP SUB-ASSEMBLY


    B203052E02
  1. Using a clip remover, detach the 4 claws.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Do not forcibly pry the assist grip plugs to prevent them from being deformed.

    HINT:
    1. Gently pry the assist grip plugs as shown in the illustration to detach the claws.
    2. Tape the clip remover tip before use.
    3. Use the same procedure for the other assist grip sub-assembly.

  1. Pull off the 2 assist grip plugs by hand.



    B203053
  1. Detach the 2 clips to remove the assist grip sub-assembly.

  1. Remove the 2 clips from the vehicle body.



22. REMOVE VISOR BRACKET COVER LH


    B181706
  1. Detach the 4 claws to remove the visor bracket cover LH.



23. REMOVE VISOR BRACKET COVER RH

HINT:
Use the same procedure as for the LH side.



24. REMOVE VISOR ASSEMBLY LH


    B181707
  1. Remove the 2 screws and visor assembly LH.



25. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



26. REMOVE VISOR HOLDER


    B151362E02
  1. Turn the visor holder approximately 45° to pull it out as shown in the illustration.

  1. Detach the 2 claws to remove the visor holder.

    HINT:
    Use the same procedure for the other visor holder.



27. REMOVE DRIVE MONITOR SWITCH (w/ Drive Monitor Switch)


    B352852
  1. Detach the 4 claws to remove the drive monitor switch.

  1. Disconnect the connector.



28. REMOVE MAP LIGHT ASSEMBLY
  1. Open the cover (w/o Drive Monitor Switch).



    B352859
  1. Remove the 2 screws.

  1. Detach the 2 clips to remove the map light assembly.

  1. Disconnect the connector.



29. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)


B262787E01
  1. Pinch the cover and detach the 2 claws. Then remove the cover.
    Text in Illustration 
    *1
    Cover



    B101367E05
  1. Pull the lever, and then slide to remove the inner rear view mirror assembly.
    Text in Illustration 
    *1
    Lever



30. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    B352853
  1. Detach the 2 guides to slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration.



    B175049
  1. Detach the 2 claws to remove the inner rear view mirror stay holder cover.



31. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)


B352854
  1. Disconnect the connector.

  1. Using a T20 "TORX" socket wrench, remove the screw and inner rear view mirror assembly.



32. REMOVE ROOF HEADLINING ASSEMBLY
  1. Partially remove the roof headlining assembly.

    HINT:
    It is not necessary to completely remove the roof headlining assembly. Slightly lower the front section of the roof headlining assembly so that the windshield glass can be removed in a later step.
    Refer to the following procedures (Click here).



33. REMOVE WINDSHIELD OUTSIDE MOULDING


    B166392E02
  1. Using a knife, cut off the windshield outside moulding as shown in the illustration.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Remove the remaining windshield outside moulding.
    Text in Illustration 
    *1
    Windshield Glass
    *2
    Windshield Outside Moulding
    *3
    Vehicle Body
    *a
    Cut

    HINT:
    Make a partial cut in the windshield outside moulding. Then pull and remove it by hand.



34. REMOVE WINDSHIELD OUTSIDE UPPER MOULDING


    B166393E03
  1. Using a knife, cut off the windshield outside upper moulding as shown in the illustration.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Pull the shaded area shown in the illustration by hand to remove the windshield outside upper moulding.
    Text in Illustration 
    *1
    Windshield Glass
    *2
    Windshield Outside Upper Moulding
    *3
    Vehicle Body
    *a
    Cut

    HINT:
    Make a partial cut in the windshield outside upper moulding. Then pull and remove it by hand.



35. REMOVE WINDSHIELD GLASS


NOTICE:
  1. There are No. 1 and No. 2 windshield glass stoppers on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.
  2. To prevent the windshield glass from dropping when performing this operation, be sure to hold the windshield glass using suction cups.

HINT:
Depending on the vehicle specifications, a 1-piece or 2-piece type stopper is used.



B238992E01


Text in Illustration 
*A
for 1-piece Type
*B
for 2-piece Type
*1
No. 1 Windshield Glass Stopper
*2
No. 2 Windshield Glass Stopper


    B238993E01
  1. Apply protective tape around the windshield glass on the vehicle body.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Apply protective tape to the installation surface to prevent it from being scratched.



    B183897E03
  1. From the interior, insert a piano wire between the vehicle body and windshield glass as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
    Text in Illustration 
    *1
    Plastic Sheet
    *2
    Protective Tape
    *3
    Windshield Glass Stopper
    *4
    Piano Wire

    NOTICE:
    1. When separating the windshield glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.
    2. To prevent the instrument panel from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and instrument panel.



    B166394E02
  1. Place matchmarks on the windshield glass and vehicle body at the locations indicated in the illustration.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Matchmarks do not need to be placed if not reusing the windshield glass.

  1. w/ Windshield Deicer System:
    Disconnect the windshield deicer connector.

  1. Cut through the adhesive by pulling the piano wire around the windshield glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the windshield glass.

  1. Disconnect the stoppers.



    B166840
  1. Using suction cups, remove the windshield glass.



36. REMOVE WINDSHIELD GLASS ADHESIVE DAM
  1. Using a scraper, remove the windshield glass adhesive dam.



37. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)
  1. Using a scraper, remove the 2 No. 1 windshield glass stoppers.



38. REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
  1. Using a scraper, remove the 2 No. 2 windshield glass stoppers.



39. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)


    B238995
  1. Remove the 2 No. 1 windshield glass stoppers.

    NOTICE:
    Be sure to replace the No. 1 windshield glass stoppers with new ones.



40. CLEAN WINDSHIELD GLASS


B106929
  1. Using a scraper, remove the damaged windshield glass stoppers, windshield glass adhesive dam and adhesive sticking to the windshield glass.

  1. Clean the outer circumference of the windshield glass with non-residue solvent.

    NOTICE:
    1. Do not touch the windshield glass surface after cleaning it.
    2. Be careful not to damage the windshield glass.
    3. Even if using new windshield glass, clean the windshield glass with non-residue solvent.



41. CLEAN VEHICLE BODY


    B106081E18
  1. Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
      Text in Illustration 
      *1
      Adhesive
      *2
      Vehicle Body

      NOTICE:
      Be careful not to damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

  1. Clean the contact surface of the vehicle body with cleaner.

    HINT:
    Even if all the adhesive has been removed, clean the vehicle body.