Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING

ROOF HEADLINING > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
(Click here)


3. REMOVE DOOR SCUFF PLATE ASSEMBLY LH


    B240006E01
  1. Put protective tape around the door scuff plate assembly LH.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides to remove the door scuff plate assembly LH.

    HINT:
    Tape the screwdriver tip before use.



4. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



5. REMOVE COWL SIDE TRIM BOARD LH


    B238734
  1. Remove the clip.

  1. Detach the clip and claw to remove the cowl side trim board LH.



6. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure as for the LH side.



7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B240007
  1. Remove the front door opening trim weatherstrip LH.



8. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



9. REMOVE ASSIST GRIP PLUG


    B238813E01
  1. Using a screwdriver, detach the 2 claws to remove the assist grip plug.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedure for the other assist grip plug.



10. REMOVE NO. 1 ASSIST GRIP


    B238814
  1. Remove the 2 bolts.

  1. Detach the 2 claws to remove the No. 1 assist grip.



11. REMOVE FRONT PILLAR GARNISH RH


    B240014
  1. Detach the clip and 3 guides to remove the front pillar garnish RH.



    B240016E01
  1. Protect the curtain shield airbag assembly.

    1. Completely cover the curtain shield airbag assembly with a protective cover and secure the ends of the cover with adhesive tape as shown in the illustration.
      Text in Illustration 
      *1
      Curtain Shield Airbag Assembly
      *2
      Adhesive Tape
      *3
      Protective Cover

      NOTICE:
      Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish RH is removed.



12. REMOVE FRONT PILLAR GARNISH LH


    B353464E01
  1. Using a screwdriver, detach the 2 claws to remove the No. 1 front pillar garnish cover LH.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    B353465
  1. Remove the bolt.

  1. Detach the clip.



    B353468
  1. Detach the 2 guides to remove the front pillar garnish LH.



    B240015E01
  1. Protect the curtain shield airbag assembly.

    1. Completely cover the curtain shield airbag assembly with a protective cover and secure the ends of the cover with adhesive tape as shown in the illustration.
      Text in Illustration 
      *1
      Curtain Shield Airbag Assembly
      *2
      Adhesive Tape
      *3
      Protective Cover

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish LH is removed.



13. REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)


    B238730E01
  1. Using a screwdriver, detach the 2 claws to remove the rear No. 1 floor step cover.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedure for all the rear No. 1 floor step covers.



14. REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)


    B238731
  1. Remove the 2 bolts and quarter scuff plate LH.



15. REMOVE QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure as for the LH side.



16. REMOVE REAR DOOR SCUFF PLATE LH
  1. Put protective tape around the rear door scuff plate LH.



    B240011E02
  1. Using a screwdriver, detach the 3 clips, 6 claws and 2 guides to remove the rear door scuff plate LH.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



17. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



18. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B240009
  1. Remove the rear door opening trim weatherstrip LH.



19. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



20. REMOVE OUTER LAP BELT ANCHOR COVER


    B238735
  1. Detach the 3 claws to remove the outer lap belt anchor cover.

    HINT:
    Use the same procedure for the other outer lap belt anchor cover.



21. REMOVE LOWER CENTER PILLAR GARNISH LH


    B238736
  1. Remove the bolt to disconnect the front seat outer belt floor anchor.



    B238737
  1. Detach the 4 claws and 2 clips to remove the lower center pillar garnish LH.



22. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure as for the LH side.



23. REMOVE CENTER PILLAR GARNISH LH


    B240017
  1. Move the front shoulder belt anchor adjuster to the lowest position.

  1. Remove the bolt.

  1. Detach the 2 clips and 2 guides.

  1. Pass the front seat outer belt floor anchor through the center pillar garnish LH to remove the center pillar garnish LH.



24. REMOVE CENTER PILLAR GARNISH RH

HINT:
Use the same procedure as for the LH side.



25. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)


    B240044
  1. Detach the 4 claws to open the cover.



    B240045E01
  1. Remove the bolt, luggage hold belt striker and No. 1 luggage compartment trim cover.
    Text in Illustration 
    *1
    Luggage Hold Belt Striker

    HINT:
    Use the same procedure for the other No. 1 luggage compartment trim cover.



26. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)


    B240046
  1. Detach the clip to remove the No. 1 deck board sub-assembly.



27. REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)


    B240062E01
  1. Using a screwdriver, detach the 4 clips and 2 guides to remove the luggage compartment side cover sub-assembly LH.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



28. REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)

HINT:
Use the same procedure as for the LH side.



29. REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)


    B353466
  1. Remove the 6 bolts.

  1. Detach the 2 guides to remove the deck board assembly.



30. REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board)


    B240048
  1. Detach the 2 claws to open the cover.



    B240049E01
  1. Remove the bolt, luggage hold belt striker and No. 2 luggage compartment trim cover.
    Text in Illustration 
    *1
    Luggage Hold Belt Striker

    HINT:
    Use the same procedure for the other No. 2 luggage compartment trim cover.



31. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board)


    B240064
  1. Detach the 2 clips and 2 guides to remove the No. 2 deck board sub-assembly.



32. REMOVE REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board)


    B240065
  1. Detach the 3 clips to remove the rear No. 2 floor board assembly.



33. REMOVE INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)


    B353467
  1. Remove the 4 bolts and inner floor side rail sub-assembly.



34. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE


    B240050
  1. Detach the 5 clips to remove the rear floor mat rear support plate.



35. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)


    B240047
  1. Detach the 4 claws to remove the rear floor carpet assembly.



36. REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER


    B240053
  1. Detach the 3 claws to remove the rear No. 1 seat outer lap belt anchor cover.

    HINT:
    Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.



37. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    B181695
  1. Remove the No. 1 luggage compartment trim hook by turning it clockwise.

    HINT:
    Use the same procedure for the other No. 1 luggage compartment trim hook.



38. REMOVE FRONT DECK SIDE TRIM COVER LH


    B240051E01
  1. Using a screwdriver, detach the 2 claws to remove the front deck side trim cover LH.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



39. REMOVE FRONT DECK SIDE TRIM COVER RH

HINT:
Use the same procedure as for the LH side.



40. REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)


    B240048
  1. Detach the 2 claws to open the cover.



    B240049E01
  1. Remove the bolt, luggage hold belt striker and No. 2 luggage compartment trim cover.
    Text in Illustration 
    *1
    Luggage Hold Belt Striker

    HINT:
    Use the same procedure for the other No. 2 luggage compartment trim cover.



41. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


  1. w/o Rear No. 2 Seat:



      B240054
    1. Remove the bolt to disconnect the rear No. 1 seat outer belt floor anchor.

    2. Remove the 3 bolts and 2 screws.



    3. Detach the 7 clips, 5 claws and 2 guides.


      B240058



    4. B238756
    5. Detach the 6 claws and 2 guides and pass the rear seatback lock control lever base through the deck trim side panel assembly LH to remove the deck trim side panel assembly LH.



  1. w/ Rear No. 2 Seat:



      B240054
    1. Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.



    2. B240052
    3. Remove the bolt to disconnect the rear No. 2 seat outer belt floor anchor.

    4. Remove the 3 bolts and 2 screws.



    5. Detach the 7 clips, 5 claws and 2 guides to remove the deck trim side panel assembly LH.


      B240060



42. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


  1. w/o Rear No. 2 Seat:



      B240057
    1. Remove the bolt to disconnect the rear No. 1 seat outer belt floor anchor.

    2. Remove the 3 bolts and screw.



    3. Detach the 7 clips, 5 claws and 2 guides.


      B240059

    4. Disconnect each connector.



    5. B238823
    6. Detach the 6 claws and 2 guides and pass the rear seatback lock control lever base through the deck trim side panel assembly RH to remove the deck trim side panel assembly RH.



  1. w/ Rear No. 2 Seat:



      B240057
    1. Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.



    2. B240055
    3. Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

    4. Remove the 3 bolts and screw.

    5. Detach the 7 clips, 5 claws and 2 guides.



    6. Disconnect each connector and remove the deck trim side panel assembly RH.


      B240061



43. REMOVE REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY LH


    B240018
  1. w/o Rear No. 2 Seat:

    1. Detach the 6 clips and guide to remove the rear No. 2 window side garnish assembly LH.



    B241940
  1. w/ Rear No. 2 Seat:

    1. Detach the 6 clips and guide.



    2. B240019
    3. Detach the 7 claws and guide and pass the rear No. 2 seat outer belt floor anchor through the rear No. 2 window side garnish assembly LH to remove the rear No. 2 window side garnish assembly LH.



44. REMOVE REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



45. REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY LH


    B240020
  1. Detach the 7 clips and 4 guides.



    B240021
  1. Detach the 4 claws and 2 guides and pass the rear No. 1 seat outer belt floor anchor through the rear window side garnish assembly LH to remove the rear window side garnish assembly LH.



46. REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



47. REMOVE ASSIST GRIP SUB-ASSEMBLY


    B203052E02
  1. Using a clip remover, detach the 4 claws.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Do not forcibly pry the assist grip plugs to prevent them from being deformed.

    HINT:
    1. Gently pry the assist grip plugs as shown in the illustration to detach the claws.
    2. Tape the clip remover tip before use.
    3. Use the same procedure for the other assist grip sub-assembly.

  1. Pull off the 2 assist grip plugs by hand.



    B203053
  1. Detach the 2 clips to remove the assist grip sub-assembly.

  1. Remove the 2 clips from the vehicle body.



48. REMOVE REAR ASSIST GRIP ASSEMBLY


    B203054E02
  1. Using a clip remover, detach the 4 claws.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Do not forcibly pry the assist grip plugs to prevent them from being deformed.

    HINT:
    1. Gently pry the rear assist grip plugs as shown in the illustration to detach the claws.
    2. Tape the clip remover tip before use.
    3. Use the same procedure for the other rear assist grip assembly.

  1. Pull off the 2 assist grip plugs by hand.



    B203055
  1. Detach the 2 clips to remove the rear assist grip assembly.

  1. Remove the 2 clips from the vehicle body.



49. REMOVE COAT HOOK


    B240022E01
  1. Using a screwdriver, detach the claw to open the cover.
    Text in Illustration 
    *1
    Protective Tape



    B240023
  1. Remove the screw and coat hook.

    HINT:
    Use the same procedure for the other coat hook.



50. REMOVE VISOR BRACKET COVER LH


    B181706
  1. Detach the 4 claws to remove the visor bracket cover LH.



51. REMOVE VISOR BRACKET COVER RH

HINT:
Use the same procedure as for the LH side.



52. REMOVE VISOR ASSEMBLY LH


    B181707
  1. Remove the 2 screws and visor assembly LH.



53. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



54. REMOVE VISOR HOLDER


    B151362E02
  1. Turn the visor holder approximately 45° to pull it out as shown in the illustration.

  1. Detach the 2 claws to remove the visor holder.

    HINT:
    Use the same procedure for the other visor holder.



55. REMOVE DRIVE MONITOR SWITCH (w/ Drive Monitor Switch)


    B352852
  1. Detach the 4 claws to remove the drive monitor switch.

  1. Disconnect the connector.



56. REMOVE MAP LIGHT ASSEMBLY
  1. Open the cover (w/o Drive Monitor Switch).



    B352859
  1. Remove the 2 screws.

  1. Detach the 2 clips to remove the map light assembly.

  1. Disconnect the connector.



57. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    B352853
  1. Detach the 2 guides to slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration.



    B175049
  1. Detach the 2 claws to remove the inner rear view mirror stay holder cover.



58. REMOVE NO. 1 ROOM LIGHT ASSEMBLY


    E189683E01
  1. Using a screwdriver, detach the 4 claws and remove the No. 1 room light lens.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape



    E189685E01
  1. Using a screwdriver, detach the 2 claws and 2 guides and remove the 2 No. 1 room light covers.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape



    E189687E01
  1. Using a screwdriver, detach the 4 claws and disconnect the No. 1 room light assembly as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape



    E189689
  1. Using a screwdriver, detach the 4 claws and disconnect the room light switch base from the No. 1 room light assembly.



59. REMOVE ROOF HEADLINING ASSEMBLY

HINT:
B240031
Before removing the roof headlining assembly, move the front seats and rear No. 1 seat to the positions shown in the illustration.



    B354490
  1. w/ EC Mirror:
    Disconnect the inner rear view mirror assembly connector.



    B240024
  1. w/ Sliding Roof:
    Disconnect the sliding roof drive gear connector.



    B360654
  1. Disconnect each connector and detach the 4 clamps from the front pillar LH.



    B240026
  1. Disconnect the connector and detach the 2 clamps from the front pillar RH.



    B240027
  1. Disconnect the connector and detach the clamp from the rear pillar RH.



    B354450
  1. w/o Sliding Roof:

    1. Remove the 5 clips.



    B354451E01
  1. w/ Sliding Roof:

    1. Remove the 5 clips.

    2. Detach the 2 guides and 8 fasteners.
      Text in Illustration 
      *1
      Guide
      *2
      Fastener



    B240030
  1. Remove the roof headlining assembly from the back door as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining assembly when remove it.



60. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


    B240077
  1. Detach the 4 claws of the front shoulder belt anchor plate sub-assembly LH to slide the front shoulder belt anchor plate sub-assembly LH to remove it.



61. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



62. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH


    B240066
  1. Detach the 3 clips to remove the roof side rail garnish assembly LH.



63. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



64. REMOVE REAR NO. 3 SIDE RAIL SPACER LH


    B240068
  1. Detach the 2 claws to remove the rear No. 3 side rail spacer LH.



65. REMOVE REAR NO. 3 SIDE RAIL SPACER RH

HINT:
Use the same procedure as for the LH side.



66. REMOVE QUARTER TRIM COVER


    B240071
  1. Detach the 2 claws to remove the quarter trim cover.

    HINT:
    Use the same procedure for the other quarter trim cover.



67. REMOVE QUARTER TRIM JACK COVER SUB-ASSEMBLY


    B240073
  1. Detach the 3 claws and 2 guides to remove the quarter trim jack cover sub-assembly.



68. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH


    B240072
  1. Detach the 2 claws and 2 guides to remove the rear combination light service cover LH.



69. REMOVE REAR COMBINATION LIGHT SERVICE COVER RH

HINT:
Use the same procedure as for the LH side.



70. REMOVE SIDE TRIM BOX LH (w/o Rear No. 2 Seat)


    B240070
  1. Remove the 2 screws.

  1. Detach the 8 claws to remove the side trim box LH.



71. REMOVE SIDE TRIM BOX RH (w/o Rear No. 2 Seat)

HINT:
Use the same procedure as for the LH side.



72. REMOVE REAR FLOOR FINISH SIDE PLATE LH (w/o Rear No. 2 Seat)


    B240074
  1. Remove the 2 screws.

  1. Detach the claw and 2 guides to remove the rear floor finish side plate LH.



73. REMOVE REAR FLOOR FINISH SIDE PLATE RH (w/o Rear No. 2 Seat)

HINT:
Use the same procedure as for the LH side.



74. REMOVE REAR SEAT SHOULDER BELT HANGER LH (w/ Rear No. 2 Seat)


B238782
  1. Detach the claw and guide to remove the rear seat shoulder belt hanger LH.



75. REMOVE REAR SEAT SHOULDER BELT HANGER RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure as for the LH side.



76. REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH (w/ Rear No. 2 Seat)


B240075
  1. Detach the 4 claws and 2 guides to remove the quarter trim lid sub-assembly RH.



77. REMOVE DECK SIDE TRIM CUP HOLDER LH (w/ Rear No. 2 Seat)


    B240076
  1. Remove the 4 screws.

  1. Detach the 2 claws to remove the deck side trim cup holder LH.



78. REMOVE DECK SIDE TRIM CUP HOLDER RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure as for the LH side.