Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR

REAR AIRBAG SENSOR > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
  1. Remove the rear No. 2 seat assembly (Click here).



3. REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)


    B238730E01
  1. Using a screwdriver, detach the 2 claws to remove the rear No. 1 floor step cover.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedure for all the rear No. 1 floor step covers.



4. REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)


    B238731
  1. Remove the 2 bolts and quarter scuff plate LH.



5. REMOVE REAR DOOR SCUFF PLATE LH
  1. Put protective tape around the rear door scuff plate LH.



    B240011E02
  1. Using a screwdriver, detach the 3 clips, 6 claws and 2 guides to remove the rear door scuff plate LH.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



6. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B240009
  1. Remove the rear door opening trim weatherstrip LH.



7. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)


    B240044
  1. Detach the 4 claws to open the cover.



    B240045E01
  1. Remove the bolt, luggage hold belt striker and No. 1 luggage compartment trim cover.
    Text in Illustration 
    *1
    Luggage Hold Belt Striker

    HINT:
    Use the same procedure for the other No. 1 luggage compartment trim cover.



8. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)


    B240046
  1. Detach the clip to remove the No. 1 deck board sub-assembly.



9. REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board)


    B240048
  1. Detach the 2 claws to open the cover.



    B240049E01
  1. Remove the bolt, luggage hold belt striker and No. 2 luggage compartment trim cover.
    Text in Illustration 
    *1
    Luggage Hold Belt Striker

    HINT:
    Use the same procedure for the other No. 2 luggage compartment trim cover.



10. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board)


    B240064
  1. Detach the 2 clips and 2 guides to remove the No. 2 deck board sub-assembly.



11. REMOVE REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board)


    B240065
  1. Detach the 3 clips to remove the rear No. 2 floor board assembly.



12. REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)


    B240062E01
  1. Using a screwdriver, detach the 4 clips and 2 guides to remove the luggage compartment side cover sub-assembly LH.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



13. REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)

HINT:
Use the same procedure as for the LH side.



14. REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)


    B353466
  1. Remove the 6 bolts.

  1. Detach the 2 guides to remove the deck board assembly.



15. REMOVE INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)


    B353467
  1. Remove the 4 bolts and inner floor side rail sub-assembly.



16. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE


    B240050
  1. Detach the 5 clips to remove the rear floor mat rear support plate.



17. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)


    B240047
  1. Detach the 4 claws to remove the rear floor carpet assembly.



18. REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER


    B240053
  1. Detach the 3 claws to remove the rear No. 1 seat outer lap belt anchor cover.

    HINT:
    Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.



19. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    B181695
  1. Remove the No. 1 luggage compartment trim hook by turning it clockwise.

    HINT:
    Use the same procedure for the other No. 1 luggage compartment trim hook.



20. REMOVE FRONT DECK SIDE TRIM COVER LH


    B240051E01
  1. Using a screwdriver, detach the 2 claws to remove the front deck side trim cover LH.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



21. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM COVER


    B240048
  1. Detach the 2 claws to open the cover.



    B240049E01
  1. Remove the bolt, luggage hold belt striker and No. 2 luggage compartment trim cover.
    Text in Illustration 
    *1
    Luggage Hold Belt Striker

    HINT:
    Use the same procedure for the other No. 2 luggage compartment trim cover.



22. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


  1. w/o Rear No. 2 Seat:



      B240054
    1. Remove the bolt to disconnect the rear No. 1 seat outer belt floor anchor.

    2. Remove the 3 bolts and 2 screws.



    3. Detach the 7 clips, 5 claws and 2 guides.


      B240058



    4. B238756
    5. Detach the 6 claws and 2 guides and pass the rear seatback lock control lever base through the deck trim side panel assembly LH to remove the deck trim side panel assembly LH.



  1. w/ Rear No. 2 Seat:



      B240054
    1. Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.



    2. B240052
    3. Remove the bolt to disconnect the rear No. 2 seat outer belt floor anchor.

    4. Remove the 3 bolts and 2 screws.



    5. Detach the 7 clips, 5 claws and 2 guides to remove the deck trim side panel assembly LH.


      B240060



23. REMOVE REAR AIRBAG SENSOR LH


    B240199
  1. Remove the nut and rear airbag sensor.

  1. Disconnect the connector.