Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Brake Warning Light Remains ON

for Preparation Click here


DESCRIPTION

The BRAKE warning light comes on when brake fluid is insufficient, the parking brake is applied or the EBD is defective.

WIRING DIAGRAM


C214520E04


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).

1.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


2.CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


3.READ VALUE USING TECHSTREAM (PARKING BRAKE SW)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Parking Brake SW
    Parking brake switch/ ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -

  1. Using the Techstream, check the input of the switch operation when the parking brake pedal is operated.

    OK:
    When the parking brake is operated, the display changes as shown above.



NG
Go to step 5
OK


4.READ VALUE USING TECHSTREAM (BRAKE WARNING LIGHT)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Brake Warning Light
    Brake warning light/ ON or OFF
    ON: Warning light on
    OFF: Warning light off
    -

  1. When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Brake Warning Light
    Brake warning light
    Warning light ON/OFF
    Observe the combination meter.


Result 
Result
Proceed to
Data List Display
Data List Display when Performing Active Test ON/OFF Operation
ON
Does not change between ON and OFF
A
Changes between ON and OFF
B
OFF
Does not change between ON and OFF
A
Changes between ON and OFF
B


B
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)  

5.INSPECT PARKING BRAKE SWITCH
  1. Disconnect the A2 parking brake switch connector.



    C215408E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Parking brake applied
    (Switch pin not pushed in)
    Below 1 Ω
    Parking brake released
    (Switch pin pushed in)
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Parking Brake Switch)



NG
REPLACE PARKING BRAKE SWITCH ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH - MAIN BODY ECU [DRIVER SIDE JUNCTION BLOCK])
  1. Disconnect the A2 parking brake switch connector.

  1. Disconnect the 2D main body ECU (driver side junction block assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A2-1 - 2D-17 (PKB)
    Always
    Below 1 Ω
    A2-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)