Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Downhill Assist Control Indicator Light does not Come ON

for Preparation Click here


DESCRIPTION

Even if the downhill assist control switch is pressed, the downhill assist control indicator light blinks and downhill assist control does not activate under the following conditions:
  1. The transfer is in H4.
  2. The brake system is malfunctioning.
  3. The temperature of the hydraulic brake booster increases and downhill assist control is temporarily canceled.

WIRING DIAGRAM


C214522E18


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).

1.CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


2.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


3.INSPECT DOWNHILL ASSIST CONTROL SWITCH
  1. Remove the downhill assist control switch (Click here).



    C215496E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (E) - 4 (+B2)
    Not pushed in
    10 kΩ or higher
    Pushed in
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Downhill Assist Control Switch)



NG
REPLACE DOWNHILL ASSIST CONTROL SWITCH (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU HDCS CIRCUIT)
  1. Disconnect the A6 skid control ECU connector.

  1. Disconnect the U4 downhill assist control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A6-44 (HDCS) - U4-4 (+B2)
    Always
    Below 1 Ω
    A6-44 (HDCS) - Body ground
    Always
    10 kΩ or higher
    U4-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.READ VALUE USING TECHSTREAM (DOWNHILL ASSIST CONTROL LIGHT)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Downhill Assist Control Light
    Downhill assist control indicator light/ ON or OFF
    ON: Indicator light on
    OFF: Indicator light off
    -

  1. When performing the Downhill Assist Control Light Active Test, check Downhill Assist Control Light in the Data List (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Downhill Assist Control Light
    Downhill assist control indicator light
    Indicator light ON/OFF
    Observe the combination meter.


Result 
Result
Proceed to
Data List Display
Data List Display when Performing Active Test ON/OFF Operation
ON
Does not change between ON and OFF
A
Changes between ON and OFF
B
OFF
Does not change between ON and OFF
A
Changes between ON and OFF
B


B
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)