Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1258    Open Circuit in Transfer 4WD Position Switch Circuit

DTC    C1340    Center Differential Lock Circuit

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
C1258*1
C1340*2
An open circuit is detected in the EXI circuit of the skid control ECU.
  1. Harness or connector
  2. Transfer system
  3. Master cylinder solenoid (Skid control ECU)
*1: for Part-time 4WD
*2: for Full-time 4WD

WIRING DIAGRAM


C291701E01


C291702E01


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).

1.CHECK TERMINAL VOLTAGE (EXI)
  1. Disconnect the A6 skid control ECU connector.



    C214161E23
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A6-27 (EXI) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)

Result 
Result
Proceed to
OK
A
NG (for Part-time 4WD)
B
NG (for Full-time 4WD)
C


B
Go to step 3

C
Go to step 4
A


2.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)  

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FOUR WHEEL DRIVE CONTROL ECU AND A.D.D. ACTUATOR)
  1. Disconnect the A6 skid control ECU connector.

  1. Disconnect the F47 four wheel drive control ECU connector.

  1. Disconnect the D1 A.D.D. actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Rear Differential Lock 
    Tester Connection
    Condition
    Specified Condition
    A6-27 (EXI) - F47-15 (ADD)
    Always
    Below 1 Ω
    A6-27 (EXI) - D1-3 (ADD)
    Always
    Below 1 Ω
    A6-27 (EXI) - Body ground
    Always
    10 kΩ or higher
    D1-4 (GND) - Body ground
    Always
    Below 1 Ω

    w/o Rear Differential Lock 
    Tester Connection
    Condition
    Specified Condition
    A6-27 (EXI) - F47-14 (ADD)
    Always
    Below 1 Ω
    A6-27 (EXI) - D1-3 (ADD)
    Always
    Below 1 Ω
    A6-27 (EXI) - Body ground
    Always
    10 kΩ or higher
    D1-4 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO TRANSFER SYSTEM (PROBLEM SYMPTOMS TABLE) (Click here)  

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FOUR WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY)
  1. Disconnect the A6 skid control ECU connector.

  1. Disconnect the F47 four wheel drive control ECU connector.

  1. Disconnect the B47 transfer shift actuator assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A6-27 (EXI) - F47-14 (P1)
    Always
    Below 1 Ω
    A6-27 (EXI) - B47-9 (CDL)
    Always
    Below 1 Ω
    A6-27 (EXI) - Body ground
    Always
    10 kΩ or higher
    B47-10 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO TRANSFER SYSTEM (PROBLEM SYMPTOMS TABLE) (Click here)