Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD

INSTRUMENT PANEL SAFETY PAD > REMOVAL

for Preparation Click here



1. TABLE OF BOLT, SCREW AND NUT


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.



B241500E01



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY
(Click here)


4. REMOVE REAR CONSOLE BOX ASSEMBLY
(Click here)


5. REMOVE DOOR SCUFF PLATE ASSEMBLY LH


    B240006E01
  1. Put protective tape around the door scuff plate assembly LH.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides to remove the door scuff plate assembly LH.

    HINT:
    Tape the screwdriver tip before use.



6. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



7. REMOVE COWL SIDE TRIM BOARD LH


    B238734
  1. Remove the clip.

  1. Detach the clip and claw to remove the cowl side trim board LH.



8. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure as for the LH side.



9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B240007
  1. Remove the front door opening trim weatherstrip LH.



10. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



11. REMOVE ASSIST GRIP PLUG


    B238813E01
  1. Using a screwdriver, detach the 2 claws to remove the assist grip plug.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedure for the other assist grip plug.



12. REMOVE NO. 1 ASSIST GRIP


    B238814
  1. Remove the 2 bolts.

  1. Detach the 2 claws to remove the No. 1 assist grip.



13. REMOVE FRONT PILLAR GARNISH RH


    B240014
  1. Detach the clip and 3 guides to remove the front pillar garnish RH.



    B240016E01
  1. Protect the curtain shield airbag assembly.

    1. Completely cover the curtain shield airbag assembly with a protective cover and secure the ends of the cover with adhesive tape as shown in the illustration.
      Text in Illustration 
      *1
      Curtain Shield Airbag Assembly
      *2
      Adhesive Tape
      *3
      Protective Cover

      NOTICE:
      Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish RH is removed.



14. REMOVE FRONT PILLAR GARNISH LH


    B353464E01
  1. Using a screwdriver, detach the 2 claws to remove the No. 1 front pillar garnish cover LH.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    B353465
  1. Remove the bolt.

  1. Detach the clip.



    B353468
  1. Detach the 2 guides to remove the front pillar garnish LH.



    B240015E01
  1. Protect the curtain shield airbag assembly.

    1. Completely cover the curtain shield airbag assembly with a protective cover and secure the ends of the cover with adhesive tape as shown in the illustration.
      Text in Illustration 
      *1
      Curtain Shield Airbag Assembly
      *2
      Adhesive Tape
      *3
      Protective Cover

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish LH is removed.



15. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    B239279
  1. w/o Smart Key System:

    1. Detach the 4 clips.

    2. Disconnect the cooler thermistor and remove the lower instrument panel finish panel assembly.



    B239276
  1. w/ Smart Key System:

    1. Detach the 4 clips.

    2. Disconnect the connector and cooler thermistor and remove the lower instrument panel finish panel assembly.



16. REMOVE NO. 2 SWITCH HOLE BASE


    B239275
  1. Detach the 6 clips and 2 guides.

  1. Disconnect each connector and remove the No. 2 switch hole base.



17. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B354467
  1. Detach the 7 clips to remove the instrument cluster finish panel sub-assembly.



18. REMOVE COMBINATION METER ASSEMBLY


    E196440
  1. Remove the 4 screws.

  1. Disconnect the connectors and remove the combination meter by pulling it up in the direction of the arrow in the illustration.



19. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    B239280E01
  1. Using a screwdriver, detach the 2 claws to open the cover.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    B239277
  1. Remove the 2 bolts <C>.

  1. Detach the 13 clips and 2 guides.

  1. Disconnect each connector and hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.



20. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B240153
  1. Remove the 4 bolts and airbag assembly.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



21. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B239284
  1. Detach the 3 clips and 2 guides to remove the No. 2 instrument panel under cover sub-assembly.



22. REMOVE LOWER INSTRUMENT COVER LH


    B239283E01
  1. Put protective tape around the lower instrument cover LH.

  1. Using a screwdriver, detach the 4 claws to remove the lower instrument cover LH.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



23. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B240162
  1. Remove the 3 bolts.

  1. Detach the 8 claws and remove the instrument panel airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



24. REMOVE INSTRUMENT PANEL BOX DOOR COVER


    B239281E01
  1. Using a screwdriver, detach the 2 claws and 2 guides to remove the instrument panel box door cover.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedure for all the instrument panel box door covers.



25. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B239282
  1. Remove the 3 screws <B> and 2 bolts <C>.

  1. Detach the 10 clips and guide.

  1. Disconnect each connector and remove the lower instrument panel sub-assembly.



26. REMOVE HEATER CONTROL ASSEMBLY


    E202382
  1. Detach the 4 clips and remove the heater control assembly.



27. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKETS (for Radio and Display Type)


    B296608
  1. Remove the 4 bolts.



    B352862
  1. Pull the radio and display receiver assembly with brackets as shown in the illustration to detach the 6 claws on the backside of the radio and display receiver assembly with brackets.



    B352326
  1. Disconnect each connector to remove the radio and display receiver assembly with brackets.



28. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKETS (for Navigation Receiver Type)


    B296608
  1. Remove the 4 bolts.



    B352862
  1. Pull the navigation receiver assembly with brackets as shown in the illustration to detach the 6 claws on the backside of the navigation receiver assembly with brackets.

  1. Disconnect each connector to remove the navigation receiver assembly with brackets.



29. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Climate Control Seat System)


    B353460
  1. Remove the 2 screws <B>.

  1. Detach the 4 clips.

  1. Disconnect 2 connectors and remove the lower center instrument cluster finish panel sub-assembly.



30. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Climate Control Seat System)


    B353461
  1. Remove the 2 screws <B>.

  1. Detach the 4 clips.

  1. Disconnect 3 connectors and remove the lower center instrument cluster finish panel sub-assembly.



31. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    B239285
  1. Detach the 4 clips and 2 guides to remove the No. 1 instrument panel register assembly.



32. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

HINT:
Use the same procedure as for the No. 1 instrument panel register assembly.



33. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B239286E01
  1. Put protective tape around the No. 1 instrument panel speaker panel sub-assembly.

  1. Using a screwdriver, detach the 2 clips, 4 claws and 3 guides to remove the No. 1 instrument panel speaker panel sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



34. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B354865E01
  1. Put protective tape around the No. 2 instrument panel speaker panel sub-assembly.

  1. Using a screwdriver, detach the 2 clips, 3 claws and 3 guides to remove the No. 2 instrument panel speaker panel sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



35. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY


  1. Remove the 2 screws.


    B240329E01


    Text in Illustration 
    *A
    for 9 Speakers
    *B
    for 8 Speakers

  1. Disconnect the connector to remove the front No. 2 speaker assembly.

    NOTICE:
    Do not touch the cone of the front No. 2 speaker assembly.



36. REMOVE DCM (TELEMATICS TRANSCEIVER)
  1. Disconnect the connectors.



    B240467
  1. Remove the bolt, nut and DCM (telematics transceiver) with bracket from the vehicle.



37. REMOVE 4 WHEEL DRIVE CONTROL ECU NO. 2 (for 4WD)
  1. for VF2A:
    Remove the 4 wheel drive control ECU No. 2 .

  1. for VF2BM:
    Remove the 4 wheel drive control ECU No. 2 .

  1. for VF4BM:
    Remove the 4 wheel drive control ECU No. 2 .



38. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
  1. Remove the 6 bolts <E> and nut <F>.

  1. Remove the 2 passenger airbag bolts and bolt labeled A.

  1. Disconnect each connector and detach the clamps and claws.



  1. Detach the 2 guides and remove the instrument panel sub-assembly.


    B354453E01


    Text in Illustration 
    *1
    Bolt <E>
    *2
    Nut <F>
    *3
    Guide
    *4
    Passenger Airbag Bolt
    *5
    Bolt A
    -
    -