Home › Audio / Visual / Telematics › CELLULAR COMMUNICATION › SAFETY CONNECT SYSTEM

DTC    B15C4    Airbag Signal Malfunction/Not Input

for Preparation Click here


DESCRIPTION

If the DCM (Telematics Transceiver) detects an error in the communication between the DCM (Telematics Transceiver) and center airbag sensor assembly as a result of the DCM (Telematics Transceiver) self check, this DTC will be set.

DTC Code
DTC Detection Condition
Trouble Area
B15C4
The DCM (Telematics Transceiver) detects an error in the signals from the center airbag sensor assembly when the ignition switch is ON.
  1. Airbag system
  2. Harness or connector
  3. Center airbag sensor assembly
  4. DCM (Telematics Transceiver)

WIRING DIAGRAM


E196665E15


INSPECTION PROCEDURE

NOTICE:
components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS (Click here)

1.CHECK FOR DTC (AIRBAG SYSTEM)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and wait for 10 seconds.

  1. Check the DTC of "AIRBAG SYSTEM" (Click here).
    Result 
    Result
    Proceed to
    DTC B15C4 is not output
    A
    DTC B15C4 is output
    B



B
GO TO AIRBAG SYSTEM (Click here)
A


2.CHECK DCM (TELEMATICS TRANSCEIVER) (GSW SIGNAL)


    E199656E01
  1. Remove the DCM (Telematics Transceiver) with the connectors connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.
    Waveform 
    Item
    Content
    Tester connection
    F39-24 (GSW) - Body ground
    Tool setting
    5.0 V/DIV., 20 ms/DIV.
    Vehicle condition
    Ignition switch ON
    Text in Illustration 
    *a
    Component with harness connected
    (DCM [Telematics Transceiver])
    Result 
    Result
    Proceed to
    Higher than A
    A
    Below A
    B
    A
    C



B
Go to step 4

C
Go to step 5
A


3.CHECK HARNESS AND CONNECTOR (FOR OPEN CIRCUIT)


    E199657E01
  1. Remove the center airbag sensor assembly with the connectors connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F33-24 (GSW3) - Body ground
    Ignition switch ON
    8.5 V or higher

    Waveform 
    Item
    Content
    Tester connection
    F33-24 (GSW3) - Body ground
    Tool setting
    5.0 V/DIV., 20 ms/DIV.
    Vehicle condition
    Ignition switch ON
    Text in Illustration 
    *a
    Component with harness connected
    (Center Airbag Sensor Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

4.CHECK HARNESS AND CONNECTOR (FOR SHORT CIRCUIT)


    E192516E27
  1. Disconnect the F39 DCM (Telematics Transceiver) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F39-24 (GSW) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to DCM [Telematics Transceiver])



NG
Go to step 6
OK


5.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The ignition switch must be off.
    2. Do not replace the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)  

6.CHECK HARNESS AND CONNECTOR (DCM - CENTER AIRBAG SENSOR ASSEMBLY)


    E196667E17
  1. Disconnect the F39 DCM (Telematics Transceiver) connector.

  1. Disconnect the F33 center airbag sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F39-24 (GSW) - F33-24 (GSW3)
    Always
    Below 1 Ω
    F39-24 (GSW) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to DCM [Telematics Transceiver])
    *b
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)