Home › Audio / Visual / Telematics › CELLULAR COMMUNICATION › SAFETY CONNECT SYSTEM

DTC    B15C5    Manual Button Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when the DCM (Telematics Transceiver) detects an open or short circuit in the manual (SOS) switch.

DTC Code
DTC Detection Condition
Trouble Area
B15C5
An open or short circuit in the manual (SOS) switch is detected.
  1. DCM (Telematics Transceiver)
  2. Map light assembly
  3. Harness or connector

WIRING DIAGRAM


E196668E13


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (MANUAL [SOS] SWITCH OPERATION)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and wait for 10 seconds.

  1. Enter the following menus: Body Electrical / Telematics / Data List.

  1. Check that the manual (SOS) switch condition displayed on the Techstream changes according to the manual (SOS) switch operation.

    Telematics 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Emergency Switch
    Manual (SOS) switch / OFF or ON
    OFF: Manual (SOS) switch not pressed
    -
    ON: Manual (SOS) switch pressed
    -
    Result 
    Result
    Proceed to
    Techstream display changes when turning manual (SOS) switch ON/OFF
    A
    Techstream display does not change when turning manual (SOS) switch ON/OFF
    B



B
Go to step 3
A


2.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The ignition switch must be off.
    2. Do not replace the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)  

3.CHECK DCM (TELEMATICS TRANSCEIVER) (SIG1 VOLTAGE)


    E197427E08
  1. Remove the DCM (Telematics Transceiver) with the connector connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F39-27 (SIG1) - F39-26 (SIG-)
    Ignition switch ON, manual (SOS) switch not pressed
    1.5 to 2.0 V

    Text in Illustration 
    *a
    Component with harness connected
    (DCM [Telematics Transceiver])



NG
Go to step 5
OK


4.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The ignition switch must be off.
    2. Do not replace the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)  

5.INSPECT MAP LIGHT ASSEMBLY (MANUAL [SOS] SWITCH)


    E179201E15
  1. Remove the map light assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    20 (SIG2) - 16 (GND)
    Manual (SOS) switch not pressed
    410 to 414 Ω
    20 (SIG2) - 16 (GND)
    Manual (SOS) switch pressed
    81 to 83 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Map Light Assembly)



NG
REPLACE MAP LIGHT ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (DCM - MAP LIGHT ASSEMBLY)


    E199654E02
  1. Disconnect the F39 DCM (Telematics Transceiver) connector.

  1. Disconnect the U2 map light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F39-27 (SIG1) - U2-20 (SIG2)
    Always
    Below 1 Ω
    F39-26 (SIG-) - U2-16 (GND)
    Always
    Below 1 Ω
    F39-27 (SIG1) - Body ground
    Always
    10 kΩ or higher
    F39-26 (SIG-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to DCM [Telematics Transceiver])
    *b
    Front view of wire harness connector
    (to Map Light Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The ignition switch must be off.
    2. Do not replace the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)