Home › Audio / Visual / Telematics › CELLULAR COMMUNICATION › SAFETY CONNECT SYSTEM

DTC    B1573    Short in Telephone Antenna Circuit

DTC    B15CB    Telematics Transceiver Antenna Disconnected

for Preparation Click here


DESCRIPTION

This DTC is stored when the DCM (Telematics Transceiver) detects an open or a short in the telephone and GPS antenna circuit. The DCM (Telematics Transceiver) sends and receives signals at a radio frequency of between 824 and 894 MHz or 1850 and 1990 MHz through the telephone and GPS antenna.

DTC Code
DTC Detection Condition
Trouble Area
B1573
The telephone and GPS antenna impedance is lower than the malfunction criterion for 10 seconds when the ignition switch is ON.
  1. DCM (telematics transceiver)
  2. Telephone and GPS antenna (telephone antenna assembly)
  3. Telephone and GPS antenna cord (No. 3 antenna cord sub-assembly)
  4. Telephone and GPS antenna cord (No. 2 antenna cord sub-assembly)
  5. Telephone and GPS antenna cord (Instrument panel wire)
B15CB
The telephone and GPS antenna impedance is lower than the malfunction criterion for 10 seconds when the ignition switch is ON.

HINT:
Refer to "Parts Location" for the installation location of the telephone and GPS antenna cord (Click here).


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and wait for 10 seconds.

  1. Perform "Health Check" and check for current DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1573 or B15CB is output
    A
    DTC B1573 and B15CB is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT TELEPHONE AND GPS ANTENNA (DCM - TELEPHONE AND GPS ANTENNA)


    E205695E06
  1. Disconnect the telephone and GPS antenna connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (TEL2) - 3a
    Always
    4 to 11 kΩ

    Text in Illustration 
    *a
    Telephone and GPS Antenna Assembly



NG
REPLACE TELEPHONE AND GPS ANTENNA (TELEPHONE ANTENNA ASSEMBLY) (Click here)
OK


3.INSPECT TELEPHONE AND GPS ANTENNA CORD (NO. 3 ANTENNA CORD SUB-ASSEMBLY)


    E205731E01
  1. Disconnect the No. 3 antenna cord sub-assembly from the telephone and GPS antenna assembly connector.

  1. Disconnect the No. 3 antenna cord sub-assembly from the No. 2 antenna cord sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 - B-3
    Always
    Below 1 Ω
    A-3a - B-3a
    Always
    Below 1 Ω
    A-3 - Body ground
    Always
    10 kΩ or higher
    A-3a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Telephone and GPS Antenna Assembly Side
    *b
    No. 2 Antenna Cord Sub-assembly Side



NG
REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 3 ANTENNA CORD SUB-ASSEMBLY)
OK


4.INSPECT TELEPHONE AND GPS ANTENNA CORD (NO. 2 ANTENNA CORD SUB-ASSEMBLY)


    E206197E03
  1. Disconnect the No. 2 antenna cord sub-assembly from the No. 3 antenna cord sub-assembly.

  1. Disconnect the No. 2 antenna cord sub-assembly from the No. 2 instrument panel wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C-3 - D-3
    Always
    Below 1 Ω
    C-3a - D-3a
    Always
    Below 1 Ω
    C-3 - Body ground
    Always
    10 kΩ or higher
    C-3a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Telephone Antenna Cord Sub-assembly Side
    *b
    No. 2 Instrument Panel Wire



NG
REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 2 ANTENNA CORD SUB-ASSEMBLY)
OK


5.INSPECT TELEPHONE AND GPS ANTENNA CORD (NO. 2 INSTRUMENT PANEL WIRE)


    E206198E03
  1. Disconnect the No. 2 instrument panel wire from the No. 2 antenna cord sub-assembly.

  1. Disconnect the No. 2 instrument panel wire from the DCM (telematics transceiver).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E-3 - G44-1 (TEL1)
    Always
    Below 1 Ω
    E-3a - G44-1a
    Always
    Below 1 Ω
    E-3 - Body ground
    Always
    10 kΩ or higher
    E-3a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    No. 2 Antenna Cord Sub-assembly Side
    *b
    DCM (Telematics Transceiver) Side



NG
REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 2 INSTRUMENT PANEL WIRE)
OK


6.REPLACE TELEPHONE AND GPS ANTENNA (TELEPHONE ANTENNA ASSEMBLY)
  1. Replace the telephone and GPS antenna with a normally functioning one and check if the same problem occurs again (Click here).

    OK:
    The system returns to normal.



NG
Go to step 7
OK

END (TELEPHONE AND GPS ANTENNA IS DEFECTIVE) 

7.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The ignition switch must be off.
    2. Do not replace the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)