DTC P0117 Engine Coolant Temperature Circuit Low Input |
DTC P0118 Engine Coolant Temperature Circuit High Input |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0117 | Engine coolant temperature sensor voltage is less than 0.47 V for 0.5 seconds or more. (1 trip detection logic) |
|
| P0118 | Engine coolant temperature sensor voltage is more than 4.698 V for 0.5 seconds or more. (1 trip detection logic) |
|
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| 120°C (248°F) | Short circuit |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the value displayed on the GTS.
| Result | Proceed to |
| -40°C (-40°F) | A |
| 120°C (248°F) | B |
| Between 75 and 100°C (167 and 212°F) | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS) |
![]() |
Disconnect the engine coolant temperature sensor connector.
Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the value displayed on the GTS.
| *1 | Engine Coolant Temperature Sensor |
| *2 | ECM |
| *a | Front view of wire harness connector (to Engine Coolant Temperature Sensor) |
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-30 (THW) - C40-2 (THW) | Always | Below 1 Ω |
| A36-29 (E1) - C40-1 (E2) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the engine coolant temperature sensor connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the value displayed on the GTS.
| *1 | Engine Coolant Temperature Sensor |
| *2 | ECM |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-30 (THW) or C40-2 (THW) - Body ground | Always | 10 kΩ or higher |
| A36-29 (E1) or C40-1 (E2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||