DTC P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| *a | Accelerator pedal fully released | *b | Accelerator pedal fully depressed |
| - | - | - | - |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2122 | VPA voltage is less than 0.303 V. (1 trip detection logic) |
|
| P2123 | VPA voltage is 4.737 V or more. (1 trip detection logic) | |
| P2127 | VPA2 voltage is less than 0.303 V. (1 trip detection logic) | |
| P2128 | VPA2 voltage is 4.737 V or more. (1 trip detection logic) | |
| P2138 | Difference in the signals from VPA and VPA2 exceeds the threshold. (1 trip detection logic) |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR) |
![]() |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
Read the values displayed on the GTS.
| *a | Depressed |
| *b | Released |
| Accelerator Pedal Operation | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2 |
| Released | 0.5 to 0.8 V | 0.5 to 0.8 V | Less than 10% |
| Depressed | 2.4 to 3.5 V | 2.4 to 3.5 V |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL SENSOR) |
Disconnect the ECM connector.
Disconnect the accelerator pedal sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A35-23 (VPA) - A23-6 (VPA1) | Always | Below 1 Ω |
| A35-29 (EPA) - A23-5 (GND1) | Always | Below 1 Ω |
| A35-21 (VCPA) - A23-4 (VC1) | Always | Below 1 Ω |
| A35-31 (VPA2) - A23-3 (VPA2) | Always | Below 1 Ω |
| A35-30 (EPA2) - A23-2 (GND2) | Always | Below 1 Ω |
| A35-22 (VCP2) - A23-1 (VC2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A35-23 (VPA) or A23-6 (VPA1) - Body ground | Always | 10 kΩ or higher |
| A35-29 (EPA) or A23-5 (GND1) - Body ground | Always | 10 kΩ or higher |
| A35-21 (VCPA) or A23-4 (VC1) - Body ground | Always | 10 kΩ or higher |
| A35-31 (VPA2) or A23-3 (VPA2) - Body ground | Always | 10 kΩ or higher |
| A35-30 (EPA2) or A23-2 (GND2) - Body ground | Always | 10 kΩ or higher |
| A35-22 (VCP2) or A23-1 (VC2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT ECM (VC VOLTAGE) |
![]() |
Disconnect the accelerator pedal sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A23-4 (VC1) - A23-5 (GND1) | Ignition Switch ON | 4.5 to 5.5 V |
| A23-1 (VC2) - A23-2 (GND2) | Ignition Switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Accelerator Pedal Sensor) |
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY |
Replace the accelerator pedal sensor assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2122, P2123, P2127, P2128 OR P2138) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P2122, P2123, P2127, P2128, and/or P2138 is output | B |
|
| ||||
| A | ||
| ||