Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit

for Preparation Click here


DESCRIPTION

The cruise control main switch is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control main switch turn on with switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM


A280663E02


INSPECTION PROCEDURE

1.READ VALUE ON GTS
E107091E21
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Select the following menu items: Powertrain / Cruise Control / Data List.

  1. Check the Data List to confirm proper functioning of the cruise control main switch.
    Text in Illustration 
    *a
    ON-OFF
    *b
    -/SET
    *c
    +/RES
    *d
    CANCEL

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Main SW M-CPU
    Cruise control main switch signal (Main CPU) / ON or OFF
    ON: cruise control main switch (ON-OFF button) pushed
    OFF: cruise control main switch (ON-OFF button) released
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    -/SET switch signal / ON or OFF
    ON: -/SET switch on
    OFF: -/SET switch off
    -
    RES/ACC Switch
    +/RES switch signal / ON or OFF
    ON: +/RES switch on
    OFF: +/RES switch off
    -

    OK:
    When the cruise control main switch is operated, the display changes as shown above.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT CRUISE CONTROL MAIN SWITCH ASSEMBLY
  1. Inspect the cruise control main switch assembly (Click here).



NG
REPLACE CRUISE CONTROL MAIN SWITCH ASSEMBLY (Click here)
OK


3.CHECK CRUISE CONTROL MAIN SWITCH WIRE
C361087E01
  1. Disconnect the cruise control main switch assembly connector.

  1. Disconnect the spiral cable with sensor sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):
    Tester Connection
    Specified Condition
    Cruise control main switch side connector terminal 3 (R) - z8-11
    Below 1 Ω
    Cruise control main switch side connector terminal 1 (B) - z8-10
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Spiral Cable with Sensor Sub-assembly)
    *b
    Front view of wire harness connector
    (to Cruise Control Main Switch Assembly)



NG
REPAIR OR REPLACE CRUISE CONTROL MAIN SWITCH WIRE
OK


4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
  1. Inspect the spiral cable with sensor sub-assembly (Click here).



NG
REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - ECM AND BODY GROUND)
  1. Disconnect the ECM connector.

  1. Disconnect the spiral cable with sensor sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A33-30 (CCS) - D77-6 (CCS)
    Always
    Below 1 Ω
    A33-4 (EC) - D77-5 (ECC)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A33-30 (CCS) or D77-6 (CCS) - Body ground
    Always
    10 kΩ or higher
    A33-4 (EC) or D77-5 (ECC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - ECM)
OK

REPLACE ECM (Click here)