DTC B27A1 Open in Driver Side Electrical Antenna Circuit |
| DTC No. | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
| B27A1 | An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (CLG1 - ANT1, CG1B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*1). |
| Any time*2 |
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
| Entry lock/unlock operation cannot be performed for driver side door | - |
| DTC No. | Data List and Active Test |
| B27A1 | Key diagnostic mode can be used to perform troubleshooting |

| 1.CHECK CONNECTOR CONNECTION CONDITION |
Turn the engine switch off.
Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and the front door outside handle assembly.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) |
Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.
Disconnect the E1*1 or F5*2 front door outside handle assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D41-12 (CLG1) - E1-6 (ANT1) | Always | Below 1 Ω |
| D41-13 (CG1B) - E1-3 (ANT2) | Always | Below 1 Ω |
| D48-11 (GND) - Body ground | Always | Below 1 Ω |
| D41-12 (CLG1) - Body ground | Always | 10 kΩ or higher |
| D41-13 (CG1B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| D41-12 (CLG1) - F5-6 (ANT1) | Always | Below 1 Ω |
| D41-13 (CG1B) - F5-3 (ANT2) | Always | Below 1 Ω |
| D48-11 (GND) - Body ground | Always | Below 1 Ω |
| D41-12 (CLG1) - Body ground | Always | 10 kΩ or higher |
| D41-13 (CG1B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER SIDE ELECTRICAL KEY ANTENNA) |

| *a | Component with harness connected (Certification ECU (smart key ECU assembly)) | *b | Waveform 1 |
| *c | Waveform 2 | - | - |
Reconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.
Reconnect the E1*1 or F5*2 front door outside handle assembly connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
| D41-12 (CLG1) - D48-11 (GND) | Procedure:
| 2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 1) |
| D41-12 (CLG1) - D48-11 (GND) | Procedure:
| 2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 1) |
| D41-13 (CG1B) - D48-11 (GND) | Procedure:
| 2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 2) |
|
| ||||
| OK | |
| 4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE DOOR) |
Temporarily replace the front door outside handle assembly with a new or normally functioning one (Click here).
| NEXT | |
| 5.CHECK DTC OUTPUT |
Clear the DTCs (Click here).
Recheck for DTCs (Click here).
|
| ||||
| OK | ||
| ||