Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)

DTC    B27A2    Open in Front Passenger Side Electrical Antenna Circuit

for Preparation Click here


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (front passenger side electrical key antenna) at intervals of 250 ms. For the certification ECU (smart key ECU assembly) to detect when the key is brought close to the vehicle, a signal requesting a response from the key is transmitted within approximately 1 m (3.28 ft.) of the front passenger side door at intervals of 250 ms. DTC B27A2 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (front passenger side electrical key antenna) (between terminals CLG2 and ANT1, or terminals CG2B and ANT2).

DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B27A2
An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (CLG2 - ANT1, CG2B - ANT2) (1 trip detection logic*1).
  1. Wire harness or connector
  2. Front door outside handle assembly (for front passenger side door)
  3. Certification ECU (smart key ECU assembly)
Any time*2
  1. *1: Only output while a malfunction is present.
  2. *2: Only when the vehicle is stopped.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for front passenger side door
-

Related Data List and Active Test 
DTC No.
Data List and Active Test
B27A2
Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM


B286267E15


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
  2. The entry and start system (for Entry Function) uses a LIN communication system and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (Click here).
  4. After repair, confirm DTC does not reoccur by performing the "DTC Output Confirmation Operation".
  5. Front door outside handle assembly (for passenger side door) has an antenna coil between ANT1 and ANT2 terminals.

1.CHECK CONNECTOR CONNECTION CONDITION
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and the front door outside handle assembly.

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
  1. Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

  1. Disconnect the F5*1 or E1*2 front door outside handle assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    D41-11 (CLG2) - F5-6 (ANT1)
    Always
    Below 1 Ω
    D41-10 (CG2B) - F5-3 (ANT2)
    Always
    Below 1 Ω
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω
    D41-11 (CLG2) - Body ground
    Always
    10 kΩ or higher
    D41-10 (CG2B) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    D41-11 (CLG2) - E1-6 (ANT1)
    Always
    Below 1 Ω
    D41-10 (CG2B) - E1-3 (ANT2)
    Always
    Below 1 Ω
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω
    D41-11 (CLG2) - Body ground
    Always
    10 kΩ or higher
    D41-10 (CG2B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER SIDE ELECTRICAL KEY ANTENNA)

B271427E16


Text in Illustration 
*a
Component with harness connected
(Certification ECU (smart key ECU assembly))
*b
Waveform 1
*c
Waveform 2
-
-
  1. Reconnect the D41 and D48 certification ECU (smart key ECU assembly) connector.

  1. Reconnect the F5*1 or E1*2 front door outside handle assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Using an oscilloscope, check the waveform.

    HINT:
    Check that the entry cancel function, which is one of the customizing settings of the entry and start system, is not set (Click here).


    OK:

    Tester Connection
    Switch Condition
    Tool Setting
    Specified Condition
    D41-11 (CLG2) - D48-11 (GND)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter not inside vehicle
    5. Electrical key transmitter brought inside detection area*1
    6. All doors locked through wireless operation
    2 V/DIV., 500 ms/DIV.
    Pulse generation
    (See waveform 1)
    D41-11 (CLG2) - D48-11 (GND)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter not inside vehicle
    5. Electrical key transmitter brought outside detection area*2
    6. All doors locked through wireless operation
    2 V/DIV., 500 ms/DIV.
    Pulse generation
    (See waveform 1)
    D41-10 (CG2B) - D48-11 (GND)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. All doors locked with electrical key transmitter sub-assembly
    2 V/DIV., 500 ms/DIV.
    Pulse generation
    (See waveform 2)

    1. *1: For details about the areas that are inside the entry function detection area, refer to Operation Check (Click here).
    2. *2: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE DOOR)
  1. Temporarily replace the front door outside handle assembly with a new or normally functioning one (Click here).


NEXT


5.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    OK:
    DTC B27A2 is not output.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY WAS DEFECTIVE)