Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

DTC    P0455    Evaporative Emission Control System Leak Detected (Gross Leak)

DTC    P0456    Evaporative Emission Control System Leak Detected (Very Small Leak)

DTC    P1451    Fuel Tank Pressure Sensor Range/Performance

DTC    P2404    Evaporative Emission System Leak Detection Pump Sense Circuit Range / Performance

for Preparation Click here


DTC SUMMARY


DTC No.
Monitoring Item
Malfunction Detection Condition
Trouble Area
Detection Timing
Detection Logic
P0455
EVAP gross leak
Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured. Reference pressure is measured at start and end of leak check.
If stabilized pressure is higher than [second reference pressure x 0.377], ECM determines that EVAP system has a large leak.
  1. Fuel cap (loose)
  2. Leakage from EVAP line (canister - fuel tank)
  3. Leakage from EVAP line (purge valve - canister)
  4. Leakage from canister pump module
  5. Leakage from fuel tank
  6. Leakage from canister
While ignition switch off
2 trip
P0456
EVAP small leak
Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured. Reference pressure measured at start and end of leak check.
If stabilized pressure is higher than second reference pressure, ECM determines that EVAP system has a small leak.
While ignition switch on
2 trip
P1451
EVAP clogged
A blockage in the EVAP system pipe is detected.
  1. Blockage in EVAP line (canister - fuel tank)
  2. Blockage in EVAP line (leak detection pump - canister)
  3. Blockage in canister pump module
While ignition switch on
2 trip
P2404
EVAP malfunction
Leak detection pump ending pressure is more than the threshold.
The difference between the leak detection pump highest pressure and lowest pressure is the threshold value or more.
The vent valve abnormality is detected.
  1. Leak detection pump
While ignition switch on
2 trip

DESCRIPTION

The description can be found in EVAP (Evaporative Emission) System (Click here).

MONITOR DESCRIPTION

5 hours*1 after the ignition switch is turned off, the leak detection pump creates negative pressure (vacuum) in the EVAP (Evaporative Emission) system. The ECM monitors for leaks and actuator malfunctions based on the EVAP pressure.

HINT:
*: If the enable conditions are not satisfied 5 hours after the ignition switch is turned off, the monitor check starts 2 hours later. If the enable conditions are still not satisfied 7 hours after the ignition switch is turned off, the monitor check starts 2.5 hours later.


Sequence
Operation
Duration
A
Leak detection pump monitor
300 seconds
B
First reference pressure measurement
40 seconds
C
Vent valve monitor
12 seconds
D
Pipe clogging monitor
900 seconds
E
Second reference pressure measurement
40 seconds
*: If only a small amount of fuel is in the fuel tank, it takes longer for the EVAP pressure to stabilize.

A285190E01


Text in Illustration 
*1
Purge valve: OFF (closed)
*2
Purge valve: ON (open)
*3
Vent Valve: OFF (vent)
*4
Vent Valve: ON (closed)
*5
Leak Detection Pump: OFF
*6
Leak Detection Pump: ON
*7
Reference Orifice (0.02 inch)
*8
Canister Pressure Sensor
*9
Canister
*10
Fuel Tank
*11
Canister Pump Module
*12
Canister Filter
*a
Operation A:
Atmospheric Pressure Measurement
*b
Operation B, E:
Reference Pressure Measurement
*c
Operation C:
EVAP System Pressure Measurement
*d
Atmospheric Pressure
*e
Negative Pressure
-
-
  1. (a) P0455: EVAP (Evaporative Emission) gross leak
    In operation D, the leak detection pump creates negative pressure (vacuum) in the EVAP system and the EVAP system pressure is measured. If the stabilized system pressure is higher than [second reference pressure x 0.377] (near atmospheric pressure), the ECM determines that the EVAP system has a large leak, illuminates the MIL and stores the DTC (2 trip detection logic).

  2. (b) P0456: EVAP very small leak
    In operation D, the leak detection pump creates negative pressure (vacuum) in the EVAP system and the EVAP system pressure is measured. If the stabilized system pressure is higher than second reference pressure, the ECM determines that the EVAP system has a small leak, illuminates the MIL and stores the DTC (2 trip detection logic).


    A281935E04


CONFIRMATION DRIVING PATTERN

NOTICE:
  1. The Evaporative System Check (Automatic Mode) consists of 5 steps performed automatically by the GTS. It takes a maximum of approximately 24 minutes.
  2. Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.
  3. Do not run the engine during this operation.
  4. When the temperature of the fuel is 35°C (95°F) or more, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F) and the coolant temperature below 45°C (113°F).

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the GTS on.
  6. Enter the following menus: Powertrain / Engine / Utility / Evaporative System Check / Automatic Mode.
  7. After the Evaporative System Check is completed, check for All Readiness by entering the following menus: Powertrain / Engine / Utility / All Readiness.
  8. Input the DTC: P0455, P0456, P1451 or P2404.
  9. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  10. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.


Result:

Result
Proceed to
DTC P0455, P0456, P1451 or P2404 is output
A
DTC P0455, P0456, P1451 or P2404 and other DTCs are output
B



B
GO TO DTC CHART (Click here)
A

GO TO EVAP SYSTEM (Click here)