Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
  1. In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
  2. The actual values may differ from the values listed in the chart under "Results of real-vehicle check" due to climate, weather conditions, etc.

HINT:
Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in P, N or neutral, the A/C switch should be off and all accessory switches should be off.

  1. Warm up the engine.

  2. Turn the A/C switch off.

  3. Turn the ignition switch off.

  4. Connect the GTS to the DLC3.

  5. Turn the ignition switch to ON.

  6. Turn the GTS on.

  7. Enter the following menus: Powertrain / Engine / Data List.

    HINT:
    1. To display the list box, press the pull down menu button next to Primary. Then select a measurement group.
    2. When you select a measurement group, the ECU data belonging to that group is displayed.
    3. Measurement Group List / Description
      1. All Data / All data
      2. Primary / -
      3. Engine Control / Engine control system related data
      4. Ptrl General / -
      5. Ptrl AF Control / Air fuel ratio control system related data
      6. Ptrl AF Control (D4) / Air fuel ratio control system related data
      7. Ptrl AF O2 Sensor / Air fuel ratio sensor and heated oxygen sensor related data
      8. Ptrl Throttle / Gasoline throttle system related data
      9. Ptrl Intake Control / Intake control system related data
      10. Ptrl Valve Control / Valve control system related data
      11. Ptrl Misfire / "Misfire" related data
      12. Ptrl Starting / "Difficult to start" related data
      13. Ptrl Rough Idle / "Rough idle" related data
      14. Ptrl Evaporative / Evaporative system related data
      15. Ptrl 2nd Air / 2nd air related data
      16. Ptrl CAT Converter / Catalyst converter related data
      17. Check Mode / Check mode related data
      18. Monitor Status / Monitor status related data
      19. Ignition / Ignition system related data
      20. Charging Control / Charging control system related data
      21. Compression / Data used during "Check the Cylinder Compression" Active Test
      22. AT / Continuously variable transaxle system related data
      23. Vehicle Information / Vehicle information

  8. According to the display on the GTS, read the Data List.

    HINT:
    1. The title used for each group of Data List items in this repair manual does not appear on the GTS. However, the name in parentheses after the title, which is a Measurement Group, does appear on the GTS. When the name shown in parentheses is selected on the GTS, all the Data List items listed for that group will be displayed.
    2. "Result of real-vehicle check" is the assessment of one vehicle. Use it only for reference.


Various Vehicle Conditions 1

Vehicle Speed 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Vehicle Speed
Vehicle speed/
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Actual vehicle speed
Yes
Diagnostic Note:
  1. This is the current vehicle speed
  2. The vehicle speed is detected using the wheel speed sensors.
    1. Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.

Engine Speed 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Speed
Engine speed/
Min.: 0 rpm, Max.: 16383 rpm
650 to 800 rpm:
Idling
Yes
Diagnostic Note:
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed.

Calculate Load 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Calculate Load
Load calculated by ECM/
Min.: 0%, Max.: 100%
15 to 40%:
Idling
Yes
Diagnostic Note:
This is the engine load calculated based on the estimated intake airflow.
Calculate Load = Estimated intake airflow / maximum intake airflow x 100 (%)
(For example, when the estimated intake airflow is the same as maximum intake airflow, Calculate Load is 100%.)

Vehicle Load 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Vehicle Load
Vehicle load/
Min.: 0%, Max.: 25700%
-
Yes
Diagnostic Note:
This is the engine intake air charging efficiency.
Vehicle Load = Current intake airflow (g/rev.) / maximum intake airflow
Maximum intake airflow = Displacement (L) / 2 x 1.2 (g/rev.)

HINT:
Due to individual engine differences, intake air temperature, etc., the value may exceed 100%.
Intake airflow (g/rev.) = Intake airflow (gm/sec) x 60 / Engine speed (rpm)
(Intake airflow (gm/sec) is MAF)


MAF 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
MAF
Airflow rate from Mass Air Flow (MAF) meter/
Min.: 0 gm/sec, Max.: 655.35 gm/sec
1.0 to 3.0 gm/sec: Idling
8 to 13 gm/sec: 3000 rpm (without load)
Yes
Diagnostic Note:
This is the intake air amount from the mass air flow meter.

Atmosphere Pressure 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Atmosphere Pressure
Atmospheric pressure/
Min.: 0 kPa (0 mmHg), Max.: 255 kPa (1912 mmHg)
Equivalent to atmospheric pressure (absolute pressure): Ignition switch ON
Yes
Diagnostic Note:
  1. This value is calculated from the intake air amount.
  2. Standard atmospheric pressure: 101 kPa (757 mmHg)
  3. For every 100 m increase in altitude, pressure drops by 1 kPa. This varies by weather.

MAP 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
MAP
intake manifold pressure/
Min.: 0 kPa (0 mmHg), Max.: 255 kPa (1912 mmHg)
80 to 110 kPa: Ignition switch ON
20 to 48 kPa: Idling (A/C off)
Yes
Diagnostic Note:
Intake manifold pressure is calculated by manifold absolute pressure sensor.

Engine Oil Temperature Sensor 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Oil Temperature Sensor
Engine oil temperature/
Min.: -40°C, Max.: 215°C
More than 85°C (185°F): After warming up
Yes
Diagnostic Note:
Engine oil temperature is calculated by engine oil temperature sensor.

Coolant Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Coolant Temp
Coolant temperature/
Min.: -40°C, Max.: 215°C
75 to 100°C (167 to 212°F): After warming up
Yes
Diagnostic Note:
This is the engine coolant temperature.

HINT:
  1. After warming up the engine, the engine coolant temperature is 75 to 100°C.
  2. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
  3. If the value is -40°C (-40°F) or higher than 120°C (248°F), the sensor circuit may be open or shorted.


Intake Air 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Intake Air
Intake air temperature/
Min.: -40°C, Max.: 215°C
Equivalent to temperature at location of mass air flow meter: Ignition switch ON
Yes
Diagnostic Note:
This is the intake air temperature.

HINT:
  1. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
  2. If the value is -40°C (-40°F) or higher than 120°C (248°F), the sensor circuit is open or shorted.


Ambient Temperature 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Ambient Temperature
Ambient temperature/
Min.: -40°C, Max.: 215°C
Equivalent to ambient air temperature: Ignition switch ON
Yes
Diagnostic Note:
This is the ambient temperature.

HINT:
  1. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.


Engine Run Time 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Run Time
Engine run time/
Min.: 0 s, Max.: 65535 s
Time after engine start
Yes
Diagnostic Note:
This is the time elapsed since the engine started.

HINT:
The time is counted only while the engine is running.


Initial Engine Coolant Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Initial Engine Coolant Temp
Initial engine coolant temperature/
Min.: -40°C, Max.: 119.3°C
-
Yes
Diagnostic Note:
This is the coolant temperature stored when the ignition switch is turned to ON.

Initial Intake Air Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Initial Intake Air Temp
Initial intake air temperature/
Min.: -40°C, Max.: 119.3°C
-
Yes
Diagnostic Note:
This is the intake air temperature stored when the ignition switch is turned to ON.

Battery Voltage 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Battery Voltage
Battery voltage/
Min.: 0 V, Max.: 65.535 V
11 to 14 V: Idling
Yes
Diagnostic Note:
If 11 V or less, characteristics of some electrical components may change.

Throttle Control 1

Accelerator Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accelerator Position
Accelerator pedal position/
Min.: 0%, Max.: 399.9%
Actual accelerator pedal position
No
Diagnostic Note:
This is the accelerator pedal position defined using the learned fully released position (sensor output) of accelerator pedal position sensor as 0% and the fully depressed position as 100%.

Accel Sens. No.1 Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Sens. No.1 Volt %
Absolute Accelerator Pedal Position (APP) No. 1/
Min.: 0%, Max.: 100%
10 to 20%: Accelerator pedal released
50 to 70%: Accelerator pedal fully depressed
Yes
Diagnostic Note:
The accelerator pedal position sensor No. 1 output is converted using 5 V = 100%.

HINT:
If there are no accelerator pedal position sensor DTCs stored, it is possible to conclude that the accelerator pedal position sensor system is normal.


Accel Sens. No.2 Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Sens. No.2 Volt %
Absolute APP No. 2/
Min.: 0%, Max.: 100%
10 to 20%: Accelerator pedal released
50 to 70%: Accelerator pedal fully depressed
Yes
Diagnostic Note:
The accelerator pedal position sensor No. 2 output is converted using 5 V = 100%.

Accel Sensor Out No.1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Sensor Out No.1
APP sensor No. 1 voltage/
Min.: 0 V, Max.: 4.980 V
0.5 to 0.8 V: Accelerator pedal released
2.4 to 3.5 V: Accelerator pedal fully depressed
No
Diagnostic Note:
This is the raw voltage from the accelerator pedal position sensor No. 1.

Accel Sensor Out No.2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Sensor Out No.2
APP sensor No. 2 voltage/
Min.: 0 V, Max.: 4.980 V
0.5 to 0.8 V: Accelerator pedal released
2.4 to 3.5 V: Accelerator pedal fully depressed
No
Diagnostic Note:
This is the raw voltage from the accelerator pedal position sensor No. 2.
Accelerator pedal position sensor No. 2 is used to monitor accelerator pedal position sensor No. 1. When there is a malfunction in sensor No. 1, the ECM uses sensor No. 2 to control the engine.

Accelerator Idle Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accelerator Idle Position
Whether or not accelerator pedal position sensor detecting released accelerator pedal/
ON or OFF
ON: Accelerator pedal released
No
Diagnostic Note:
This is a parameter calculated by the ECM which indicates whether the accelerator pedal is in the learned idle position.

Accel Fully Close Learn #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Fully Close Learn #1
Accelerator fully released learned value No. 1/
Min.: 0 deg, Max.: 124.5 deg
2.5 to 6.5 deg: Ignition switch ON
No
Diagnostic Note:
This is the value of accelerator pedal position sensor No. 1 learned when the accelerator pedal is released.

Accel Fully Close Learn #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Fully Close Learn #2
Accelerator fully released learned value No. 2/
Min.: 0 deg, Max.: 124.5 deg
2.5 to 6.5 deg: Ignition switch ON
No
Diagnostic Note:
This is the value of accelerator pedal position sensor No. 2 learned when the accelerator pedal is released.

Throttle Sensor Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Sensor Volt %
Absolute throttle position sensor/
Min.: 0%, Max.: 100%
  1. 10 to 22%: Throttle fully closed
  2. 80 to 90%: Throttle fully open
Yes
Diagnostic Note:
The throttle position sensor No. 1 output is converted using 5 V = 100%.

Throttle Sensor #2 Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Sensor #2 Volt %
Throttle sensor position #2/
Min.: 0%, Max.: 100%
  1. 35 to 45%: Throttle fully closed
  2. 80 to 90%: Throttle fully open
Yes
Diagnostic Note:
The throttle position sensor No. 2 output is converted using 5 V = 100%.

ST1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ST1
Brake pedal signal/
ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
No
Diagnostic Note:
This is the stop light switch signal.

Throttle Idle Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Idle Position
Whether or not throttle position sensor detecting idle/
ON or OFF
ON: Accelerator pedal released
No
Diagnostic Note:
This is a parameter calculated by the ECM.
The value is ON when the throttle is at the idle position and OFF when the throttle is open.

Throttle Require Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Require Position
Required throttle position/
Min.: 0 V, Max.: 4.980 V
0.5 to 1.1 V: Idling at P, N or neutral (A/C off)
No
Diagnostic Note:
This is a value calculated by the ECM showing the voltage for the target throttle valve position.

Throttle Sensor Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Sensor Position
Throttle sensor position/
Min.: 0%, Max.: 100%
  1. 3 to 5%: Throttle fully closed
  2. 65 to 75%: Throttle fully open
Yes
Diagnostic Note:
This is the throttle valve opening amount used for engine control.
This value has no meaning when the ignition switch is ON and the engine is stopped.

Throttle Position No. 1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Position No. 1
Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.980 V
0.213 to 4.772 V: Ignition switch ON
No
Diagnostic Note:
This is the throttle position sensor No. 1 output voltage.

Throttle Position No. 2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Position No. 2
Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.980 V
0.213 to 4.772 V: Ignition switch ON
No
Diagnostic Note:
This is the throttle position sensor No. 2 output voltage.

Throttle Position Command 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Position Command
Throttle position command value/
Min.: 0 V, Max.: 4.980 V
-
No
Diagnostic Note:
Throttle Position Command is the same value as Throttle Require Position.

Throttle Sens Open Pos #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Sens Open Pos #1
Throttle position sensor No. 1/
Min.: 0 V, Max.: 4.980 V
0.7 to 1.1 V: Ignition switch ON
No
Diagnostic Note:
This is the throttle position sensor No. 1 output voltage when there is no current supplied to the electronic throttle actuator. The accelerator pedal is released but the throttle valve is kept open by the throttle valve opener with the ignition switch ON.

Throttle Sens Open Pos #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Sens Open Pos #2
Throttle position sensor No. 2/
Min.: 0 V, Max.: 4.980 V
0.7 to 1.1 V: Ignition switch ON
No
Diagnostic Note:
This is the throttle position sensor No. 2 output voltage when there is no current supplied to the electronic throttle actuator. The accelerator pedal is released but the throttle valve is kept open by the throttle valve opener with the ignition switch ON.

Throttle Motor Power Supply Relay 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Motor Power Supply Relay
Throttle motor power supply relay/
ON or OFF
ON: Ignition switch ON
No

Throttle Motor DUTY 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Motor DUTY
Throttle actuator/
Min.: 0%, Max.: 100%
2 to 5%: Idling at P, N or neutral (A/C off)
Yes
Diagnostic Note:
This is the output duty ratio of the throttle actuator drive circuit.

Throttle Motor Duty (Open) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Motor Duty (Open)
Throttle actuator duty ratio (open)/
Min.: 0%, Max.: 255%
0 to 40%: Idling at P, N or neutral (A/C off)
No
Diagnostic Note:
This is the duty ratio used to drive the throttle actuator and open the throttle valve. It is an ECM command signal.

Throttle Motor Duty (Close) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Motor Duty (Close)
Throttle actuator duty ratio (close)/
Min.: 0%, Max.: 255%
0 to 40%: Idling at P, N or neutral (A/C off)
No
Diagnostic Note:
This is the duty ratio used to drive the throttle actuator and close the throttle valve. It is an ECM command signal.

HINT:
During idling, the throttle valve opening angle is usually controlled using a duty ratio drive signal which closes the throttle valve. However, when carbon deposits build up, it may be necessary to open the throttle valve more than the throttle valve opener does. In that case, the opening angle is controlled using a "Throttle Motor Duty (Open)" signal which opens the throttle valve.


Throttle Fully Close Learn 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Fully Close Learn
Throttle valve fully closed (learned value)/
Min.: 0 V, Max.: 4.980 V
0.35 to 0.85 V: Ignition switch ON
No
Diagnostic Note:
  1. The ECM uses this learned value to determine the fully closed (and fully open) position of the throttle valve.
  2. Learning is performed immediately after the ignition switch is turned to ON.

+BM Voltage 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
+BM Voltage
+BM voltage/
Min.: 0 V, Max.: 79.998 V
11 to 14 V: Ignition switch ON
No
Diagnostic Note:
This is the power supply for the electronic throttle actuator.

Actuator Power Supply 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Actuator Power Supply
Actuator power supply/
ON or OFF
ON: Ignition switch ON
No
Diagnostic Note:
If +BM power is lost, this item changes to OFF.

Throttle Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Position
Throttle valve opening angle/
Min.: 0 deg, Max.: 499.99 deg
-
Yes
Diagnostic Note:
This value has no meaning when the ignition switch is ON and the engine is stopped.

Idle Speed Control

ISC Flow 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ISC Flow
Flow rate calculated using information from each sensor/
Min.: 0 g/s, Max.: 299.99 g/s
-
Yes
Diagnostic Note:
This is the total ISC airflow amount (the amount of intake air necessary to maintain idling).

HINT:
ISC Flow (total ISC airflow amount) = ISC Learning Value + ISC Feedback Value + each compensation amount


ISC Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ISC Position
Requested throttle opening amount calculated using ISC control/
Min.: 0 deg, Max.: 499.99 deg
-
Yes
Diagnostic Note:
This is the throttle valve opening amount while the engine is idling (the throttle valve opening amount necessary to maintain ISC air flow).

ISC Feedback Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ISC Feedback Value
ISC feedback amount/
Min.: -150 g/s, Max.: 149.99 g/s
-
Yes
Diagnostic Note:
This is the feedback amount necessary to adjust the airflow amount to maintain the target idling speed.

HINT:
When the idling speed differs from the target, the feedback amount is adjusted. If the feedback amount becomes more than a certain value, this will be reflected in the ISC learned airflow value.


ISC Learning Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ISC Learning Value
ISC learned airflow value/
Min.: -150 g/s, Max.: 149.99 g/s
-
Yes
Diagnostic Note:
This is the learned value of the airflow amount necessary for engine idling.

HINT:
  1. If ISC Feedback Value becomes more than a certain value, this will be reflected in ISC Learning Value.
  2. ISC Flow (total ISC airflow amount) = ISC Learning Value + ISC Feedback Value + each compensation amount


Electric Load Feedback Val 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Electric Load Feedback Val
Compensation flow rate according to electrical load/
Min.: -150 g/s, Max.: 149.99 g/s
-
Yes
Diagnostic Note:
This is the ISC compensation amount determined according to the electrical load.

Air Conditioner FB Val 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Air Conditioner FB Val
Compensation flow rate according to air conditioner load/
Min.: -150 g/s, Max.: 149.99 g/s
-
Yes
Diagnostic Note:
This is the ISC compensation amount determined according to the air conditioner load.

Deposit Loss Flow 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Deposit Loss Flow
Flow loss due to deposits/
Min.: -150 g/s, Max.: 149.99 g/s
-
Yes
Diagnostic Note:
  1. This value indicates the amount of compensation for a decrease in flow passage area due to the buildup of deposits on the throttle valve.
  2. Check this value for reference when the engine stalls, is difficult to start, or idles roughly.
  3. When the ISC learned value is initialized by disconnecting the battery negative terminal or removing the EFI(+B) fuse , performing the following procedures in order to quickly relearn the Deposit Loss Flow value. After the Deposit Loss Flow has been relearned, gradual fine adjustments will continue automatically.
    1. Start the engine cold and allow the engine to idle.
    2. After the engine is warmed up (engine coolant temperature is above 80°C [176°F]), allow the engine to idle for an additional 5 minutes.
    3. Turn the ignition switch off and wait for 30 seconds.
    4. Start the engine again, and allow the engine to idle for 5 minutes.

Fuel System

Fuel Press 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel Press
Fuel pressure/
Min.: 0 kPa (0 kgf/cm2, 0 psi), Max.: 655350 kPa (6683 kgf/cm2, 95050 psi)
3000 to 5000 kPa (30.6 to 51.0 kgf/cm2, 435 to 725 psi): Idling at P, N or neutral after warming up (A/C off)
Yes
Diagnostic Note:
This item indicates the fuel pressure on the high-pressure side.

Fuel Pump Duty 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel Pump Duty
Fuel pump duty/
Min.: 0%, Max.: 399.9%
20 to 70%: Idling
Yes

Fuel Level Sensor Impedance 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel Level Sensor Impedance
Fuel Level Sensor Impedance/
Min.: 0 Ohm, Max.: 511.5 Ohm
  1. 12 to 18 Ohm: Fuel receiver gauge is F position
  2. 404 to 416 Ohm: Fuel receiver gauge is empty position
Yes

Injector (Port) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Injector (Port)
Injection period of the No. 1 cylinder/
Min.: 0 μs, Max.: 65535 μs
1000 to 2000 μs
Idling after warming up
Yes
Diagnostic Note:
This is the injection period of the No. 1 cylinder (the command value from the ECM).

Injection Volume (Cylinder 1) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Injection Volume (Cylinder 1)
Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml
0 to 0.15 ml: Idling after warming up
Yes
Diagnostic Note:
This is the fuel injection volume for 10 injections.

Fuel Pressure Target Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel Pressure Target Value
Target fuel pressure/
Min.: 0 MPa, Max.: 65.535 MPa
  1. 3 to 5 MPa (31 to 51 kgf/cm2, 435 to 725 psi): Idling after warming up
  2. 7 to 9 MPa (72 to 91 kgf/cm2, 1024 to 8924 psi): 2500 rpm (without load)
Yes
Diagnostic Note:
This item indicates the target fuel pressure for the high-pressure fuel pump.

HP FP Discharge Rate 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
HP FP Discharge Rate
Fuel volume required by the high pressure fuel pump/
Min.: 0 ml, Max.: 2.047 ml
0.04 to 0.08 ml: Idling at P, N or neutral after warming up (A/C off)
Yes
Diagnostic Note:
This item indicates the high-pressure fuel pump discharge amount.

Injection Way 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Injection Way
Injection mode/
Port / Direct / Either
-
Yes
Diagnostic Note:
This item indicates the injection mode.

Injection Switching Status 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Injection Switching Status
Prohibition of changing the D-4S injection method/
OK or NG
-
No
Diagnostic Note:
This item indicates whether the Control the Injection Way Active Test is prohibited.

Injection Timing (D4) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Injection Timing (D4)
Injection timing/
Min.: -3277 deg(CA), Max.: 3276.7 deg(CA)
320 to 340 deg(CA): Idling at P, N or neutral after warming up (A/C off)
Yes
Diagnostic Note:
This item indicates the injection timing of the main injector.

Injection Time (D4) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Injection Time (D4)
Injection time/
Min.: 0 μs, Max.: 65535 μs
0 to 2000 μs: Idling at P, N or neutral after warming up (A/C off)
Yes
Diagnostic Note:
This item indicates the last injection time of the injector for the number 1 cylinder.

EVAP System 1

Vacuum Pump 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Vacuum Pump
Key-off EVAP system pump status/
ON or OFF
-
Yes
Diagnostic Note:
This item changes to ON during the key-off EVAP monitor which is performed approximately 5 hours after the ignition switch is turned off (Click here).

EVAP System 2

EVAP (Purge) VSV 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
EVAP (Purge) VSV
Purge VSV control duty/
Min.: 0%, Max.: 100%
-
Yes
Diagnostic Note:
  1. This is the command signal from the ECM.
  2. This is the purge valve control duty ratio. When EVAP (Purge) VSV is any value except 0%, EVAP purge* is being performed.
    *: Gasoline vapor from the fuel tank is being introduced into the intake system via the purge valve.
  3. When the engine is cold or immediately after the engine is started, EVAP (Purge) VSV is 0%.

Evap Purge Flow 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Evap Purge Flow
Purge flow/
Min.: 0%, Max.: 399.9%
-
Yes
Diagnostic Note:
This is the percentage of total engine airflow contributed by EVAP purge operation.
(Evap Purge Flow = Purge flow / Engine airflow x 100 (%))

Purge Density Learn Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Purge Density Learn Value
Purge density learned value/
Min.: -200%, Max.: 199.993%
-
Yes
Diagnostic Note:
Purge Density Learn Value is the proportion of the decrease in injection volume (based on the change in the air fuel ratio feedback compensation value) related to a 1% purge flow rate.
When Purge Density Learn Value is a large negative value, the purge effect is large.
The purge density is determined from the change in the air fuel ratio feedback compensation value when purge flow is introduced.
Purge density learning is performed so that the feedback compensation value is 0 +/-2%.

HINT:
  1. Usually, the value is approximately +/-1%.
  2. 1%: The concentration of HC in the purge gas is relatively low.
  3. 0%: The concentration of HC in the purge gas is approximately equal to the stoichiometric air fuel ratio.
  4. Large negative values indicate that the concentration of HC in the purge gas is relatively high.


Vapor Pressure Pump 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Vapor Pressure Pump
Vapor pressure/
Min.: 0 kPa (0 mmHg), Max.: 327.675 kPa (2458 mmHg)
Approximately 100 kPa (750 mmHg): Ignition switch ON
Yes
Diagnostic Note:
This is the EVAP system pressure monitored by the canister pressure sensor.

HINT:
  1. Except for when the monitor is running, this value should be approximately the same as atmospheric pressure.
  2. As Vapor Pressure Pump is almost the same as Atmosphere Pressure when the engine is stopped, these items can be used to help determine if the canister pressure sensor characteristics are abnormal, if there is noise, or if the sensor output is stuck at a certain value.


EVAP System Vent Valve 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
EVAP System Vent Valve
Key-off EVAP system vent valve status/
ON or OFF
OFF: Vent
ON: Close
No

EVAP Purge VSV 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
EVAP Purge VSV
VSV status for EVAP control/
ON or OFF
-
No
Diagnostic Note:
This parameter displays ON when EVAP (Purge) VSV is 30% or more, and displays OFF when the VSV duty ratio is less than 30%.

Purge Cut VSV Duty 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Purge Cut VSV Duty
Purge VSV duty/
Min.: 0%, Max.: 399.9%
-
No
Results of real-vehicle check:
  1. Idling (warm up the engine): 0.0%
  2. Running without load (3000 rpm): 33.3%

Air Fuel Ratio Control 1

Target Air-Fuel Ratio 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Target Air-Fuel Ratio
Target air fuel ratio/
Min.: 0, Max.: 1.99
0.8 to 1.2: During idling
Yes
Diagnostic Note:
This is the target air fuel ratio used by the ECM.
  1. 1.0 is the stoichiometric air fuel ratio. Values that are more than 1 indicate the system attempting to make the air fuel ratio leaner. Values that are less than 1 indicate the system attempting to make the air fuel ratio richer.
  2. Target Air-Fuel Ratio and AF Lambda B1S1 are related.

Air Fuel Ratio Control 2

AF Lambda B1S1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
AF Lambda B1S1
Output air fuel ratio associated/
Min.: 0, Max.: 1.999
  1. Value less than 1 (0.000 to 0.999) = Rich
  2. 1 = Stoichiometric air fuel ratio
  3. Value more than 1 (1.001 to 1.999) = Lean
Yes
Diagnostic Note:
This is the actual air fuel ratio calculated based on the air fuel ratio sensor output.
Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check the voltage output of the sensor.

AFS Voltage B1S1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
AFS Voltage B1S1
Air fuel ratio sensor output voltage/
Min.: 0 V, Max.: 7.999 V
About 2.2 V: Idling (warming up the engine)
Yes
Diagnostic Note:
  1. This is the voltage output of the air fuel ratio sensor (the voltage cannot be measured at the terminals of the sensor). This value is calculated by the ECM based on the current output of the air fuel ratio sensor (refer to AFS Current B1S1 below for the actual sensor output).
  2. Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check the voltage output of the sensor.

AFS Current B1S1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
AFS Current B1S1
Air fuel ratio sensor output current /
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Yes
Diagnostic Note:
  1. With a stoichiometric air fuel ratio (for example, during idling after the engine is warmed up), the air fuel ratio sensor current output is approximately -0.5 to 0.5 mA.
  2. When the value is outside the range of 0.7 to 2.2 mA when the fuel-cut is being performed, there is a malfunction in the air fuel ratio sensor or sensor circuit.

A/F Sensor Impedance B1S1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Sensor Impedance B1S1
Air fuel ratio sensor impedance/
Min.: 0 Ohm, Max.: 6553.5 Ohm
About 32 Ohm: Idling after warming up
Yes

A/F Heater Duty #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Heater Duty #1
Air fuel ratio sensor heater duty ratio/
Min.: 0%, Max.: 399.9%
0 to 100%
Yes
Diagnostic Note:
When the value is any value except 0%, current is being supplied to the heater.

O2S B1S2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
O2S B1S2
Heated oxygen sensor output voltage /
Min.: 0 V, Max.: 1.275 V
0 to 0.9 V: Vehicle driven at constant speed of 70 km/h (44mph)
Yes
Diagnostic Note:
This is the output voltage of the heated oxygen sensor.
  1. Values close to 0 V indicate an air fuel ratio leaner than the stoichiometric ratio.
  2. Values close to 1 V indicate an air fuel ratio richer than the stoichiometric ratio.
  3. During air fuel ratio feedback control, the value moves back and forth in the range of 0 to 1 V.
Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check voltage output of the sensor.

O2 Heater B1S2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
O2 Heater B1S2
Heated oxygen sensor heater/
Not Act or Active
-
Yes

O2 Sensor Heater Duty 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
O2 Sensor Heater Duty
Oxygen sensor heater duty ratio/
Min.: 0%, Max.: 400%
0 to 100%
Yes
Diagnostic Note:
When the vehicle is any valve except 0%, current is being supplied to the heater.

Short FT #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Short FT #1
Short-term fuel trim /
Min.: -100%, Max.: 99.2%
-15 to +15%
Yes
Diagnostic Note:
This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the air fuel ratio sensor for feedback.

Long FT #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Long FT #1
Long-term fuel trim /
Min.: -100%, Max.: 99.2%
-15 to +15%
Yes
Diagnostic Note:
The ECM will learn the Long FT values based on Short FT. The goal is to keep Short FT at 0% to keep the A/F mixture at the stoichiometric ratio.
This value is used to determine whether the system related to air fuel ratio control is malfunctioning.
The condition of the system is determined based on the sum of Short FT and Long FT (excluding times when the system is in transition).
  1. +15% or more: There may be a lean air fuel ratio.
  2. -15 to +15%: The air fuel ratio can be determined to be normal.
  3. -15% or less: There may be a rich air fuel ratio.
  4. The learned value is cleared when the battery cable is disconnected.
  5. Air fuel ratio feedback leaning is divided up according to the engine operating range (engine speed * load), and separate value are stored for each operating range. "Long FT #1" indicates the learned value for the current operating range.
    [A/F Learn Value Idle #1], [A/F Learn Value Low #1], [A/F Learn Value Mid1 #1], [A/F Learn Value Mid2 #1] and [A/F Learn Value High #1] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range.

Fuel System Status #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel System Status #1
Fuel system status/
ON or OFF
-
Yes

Ignition System

IGN Advance 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
IGN Advance
Ignition timing advance for No. 1 cylinder/
Min.: -64 deg., Max.: 63.5 deg.
BTDC -5 to 10 deg.: Idling at N position
Yes

Knock Feedback Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Knock Feedback Value
Knocking feedback value/
Min.: -1024 deg(CA), Max.: 1023.9 deg(CA)
-
Yes
Diagnostic Note:
This is the ignition timing retard compensation amount determined by the presence or absence of knocking.
Ignition timing = Most retarded timing value*1 + Knock Correct Learn Value*2 + Knock Feedback Value*3
Example: 21 deg(CA) = 10° + 14° - 3°
*1: The most retarded timing value is a constant determined by the engine speed and engine load.
*2: The knock correction learned value is calculated as shown below in order to keep Knock Feedback Value as close to -3 deg(CA) as possible.
When Knock Feedback Value is less than -4 deg(CA), Knock Correct Learn Value is slowly decreased.
When Knock Feedback Value is more than -2 deg(CA), Knock Correct Learn Value is slowly increased.
*3: The base value is -3 deg(CA) and is adjusted based on the presence or absence of knocking. When there is no knocking, the value is increased, and when knocking is present, the value is decreased.

HINT:
If Knock Feedback Value does not change around the time when knocking occurs even though knocking continues (for example, stays at -3 deg(CA)), it can be determined that knocking is not being detected.
Possible Causes:
  1. There is a problem with the knock sensor sensitivity.
  2. The knock sensor is improperly installed.
  3. There is a problem with a wire harness.


Knock Correct Learn Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Knock Correct Learn Value
Knocking correction learned value/
Min.: -1024 deg(CA), Max.: 1023.9 deg(CA)
-
Yes
Diagnostic Note:
Refer to "Knock Feedback Value".
When there is knocking or a lack of power, compare the following values to another vehicle of the same model.
  1. Engine speed
  2. Calculate Load
  3. IGN Advance
  4. Knock Feedback Value
  5. Knock Correct Learn Value
Knock Correct Learn Value is large: There is no knocking and the ignition timing is advanced.
Knock Correct Learn Value is small: Knocking is present and the ignition timing is being retarded.

HINT:
When knocking continues even though Knock Correct Learn Value is less than that of the vehicle being used for comparison (in other words, the ignition timing is being retarded but the knocking is not stopping), there may be a buildup of deposits or other such problems due to deterioration over time (oil entering the cylinders, poor quality fuel, etc.).


Idle Spark Advn Ctrl #1 to #4 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Idle Spark Advn Ctrl #1
Idle Spark Advn Ctrl #2
Idle Spark Advn Ctrl #3
Idle Spark Advn Ctrl #4
Individual cylinder timing advance compensation amount (No. 1 to No. 4)/
Min.: -16 deg(CA), Max.: 15.875 deg(CA)
-
Yes
Diagnostic Note:
  1. This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.
  2. It may be possible to use this item to help determine specific cylinders which are not operating normally.

VVT Control 1

VVT Aim Angle #1, #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Aim Angle #1, #2
VVT hold duty learned value for bank 1 (bank 2)/
Min.: 0%, Max.: 399.9%
-
Yes
Diagnostic Note:
This value represents the duty ratio necessary to operate the camshaft timing oil control valve in order to block the camshaft timing oil control valve path and maintain the advanced state of the VVT controller. This is only available during the Active Test.

VVT Change Angle #1, #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Change Angle #1, #2
VVT displacement angle for bank 1 (bank2)/
Min.: -320 DegFR, Max.: 320 DegFR
-
Yes
Diagnostic Note:
This is the VVT displacement angle during forced operation.
This is only available during the Active Test.
By checking the VVT Change Angle during the Active Test, it is also possible to determine whether or not the VVT sensor signal is being output.

VVT OCV Duty #1, #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT OCV Duty #1, #2
VVT camshaft timing oil control valve operation duty for bank 1 (bank2)/
Min.: 0%, Max.: 399.9%
-
Yes
Diagnostic Note:
This is the requested duty value for forced operation.
This is only available during the Active Test.

VVT Ex Hold Lrn Val #1, #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Ex Hold Lrn Val #1, #2
VVT exhaust hold duty ratio learned value for bank 1 (bank2)/
Min.: 0%, Max.: 399.9%
-
Yes
Diagnostic Note:
This value represents the duty ratio necessary to operate the camshaft timing oil control valve in order to block the camshaft timing oil control valve path and maintain the advanced state of the VVT controller. This is only available during the Active Test.

VVT Ex Chg Angle #1, #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Ex Chg Angle #1, #2
VVT exhaust displacement angle for bank 1 (bank2)/
Min.: 0 DegFR, Max.: 639.9 DegFR
-
Yes
Diagnostic Note:
This is the displacement angle during forced operation. This is only available during the Active Test.

VVT Ex OCV Duty #1, #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Ex OCV Duty #1, #2
VVT exhaust camshaft timing oil control valve duty for bank 1 (bank2)/
Min.: 0%, Max.: 399.9%
-
Yes
Diagnostic Note:
This is the requested duty value for forced operation.
This is only available during the Active Test.

Target VVT Angle #1, #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Target VVT Angle #1, #2
Target VVT angle for bank 1 (bank2)/
Min.: -320 DegFR, Max.: 320 DegFR
-
Yes
Diagnostic Note:
This is only available during the Active Test.

Target VVT Ex Angle #1, #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Target VVT Ex Angle #1, #2
Target VVT exhaust angle for bank 1 (bank2)/
Min.: 0 DegFR, Max.: 640 DegFR
-
Yes
Diagnostic Note:
This is only available during the Active Test.

VVT OCV Current #1, #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT OCV Current #1, #2
VVT camshaft timing oil control valve output current for bank 1 (bank2)/
Min.: 0 A, Max.: 1.99 A
0.55 to 0.85 A: Idling after warming up
Yes
Diagnostic Note:
This is only available during the Active Test.

VVT Ex OCV Current #1, #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Ex OCV Current #1, #2
VVT exhaust camshaft timing oil control valve output current for bank 1 (bank2)/
Min.: 0 A, Max.: 1.99 A
0.65 to 0.80 A: Idling after warming up
Yes
Diagnostic Note:
This is only available during the Active Test.

VN Turbo

VN Turbo Type 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VN Turbo Type
Turbo type/
Not/Commo/Vacuum/CAN
Not
No
Diagnostic Note:
This is the type of the turbo charger.

Catalyst

Catalyst Temp B1S1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Catalyst Temp B1S1
Catalyst temperature/
Min.: -40°C, Max.: 6513.5°C
-
Yes
Diagnostic Note:
This is the temperature of the front catalyst estimated by the ECM.

Various Vehicle Conditions 2

Starter Signal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Starter Signal
Starter signal/
ON or OFF
ON: Starter operating
OFF: Starter not operating
No

Starter Control 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Starter Control
Starter signal/
ON or OFF
ON: Starter operating
OFF: Starter not operating
Yes

Starter Cut Relay 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Starter Cut Relay
Starter cut relay/
ON or OFF
OFF: Cranking
Yes

ACC Relay 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ACC Relay
ACC relay/
ON or OFF
ON: Ignition switch ON or cranking
OFF: Ignition switch off or after engine start
Yes

Neutral Position SW Signal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Neutral Position SW Signal
PNP switch status/
ON or OFF
ON: Shift lever in P, N or neutral
Yes

Clutch Switch 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Clutch Switch
Clutch switch status/
ON or OFF
ON: Clutch pedal depressed
OFF: Clutch pedal released
Yes

Stop Light Switch 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Stop Light Switch
Stop light switch status/
ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
Yes

A/C Signal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/C Signal
A/C switch status/
ON or OFF
ON: A/C on
Yes

A/C Pressure Normal SW 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/C Pressure Normal SW
Air conditioning pressure sensor status/
ON or OFF
ON: Air conditioning pressure sensor on
Yes

Closed Throttle Position SW 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Closed Throttle Position SW
Closed throttle position switch/
ON or OFF
ON: Throttle fully closed
OFF: Throttle open
Yes

Rear Defogger SW 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Rear Defogger SW
Rear defogger switch/
ON or OFF
ON: Rear defogger switch ON
Yes

Blower Fan SW 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Blower Fan SW
Blower fan switch/
ON or OFF
ON: Blower fan switch ON
Yes

Head Light Switch 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Head Light Switch
Head light switch/
ON or OFF
ON: light control switch tail on
Yes

Front Wiper Switch 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Front Wiper Switch
Front wiper switch/
ON or OFF
ON: Front wiper switch ON
Yes

Ignition Status 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Ignition Status
Ignition switch/
ON or OFF
ON: Ignition switch ON
Yes

Fuel Cut Condition 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel Cut Condition
Fuel cut condition/
ON or OFF
ON: Fuel cut operating
Yes

Check Mode

Check Mode 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Check Mode
Check mode/
ON or OFF
ON: Check mode on
No

Test Result

Monitor Information 1 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stored as Freeze Frame Data
NSW Test Result
N position monitor/
Compl or Incmpl
-
*1
No
OXS1 Test Result
Check mode result for heated oxygen sensor /
Compl or Incmpl
-
*1
No
A/F Test Results #1
Check mode result for air fuel ratio sensor/
Compl or Incmpl
-
*1
No
Starter SW Test Result
Check mode result for starter switch/
Compl or Incmpl
-
*1
No
Complete Parts Monitor
Comprehensive component monitor/
Not Avl or Avail
-
*1
No
Fuel System Monitor
Fuel system monitor/
Not Avl or Avail
-
*1
No
Misfire Test Result
Check mode result for misfire monitor/
Not Avl or Avail
-
*1
No
EGR/VVT Monitor
EGR/VVT monitor/
Not Avl or Avail
-
*1
No
EGR/VVT Monitor
EGR/VVT monitor/
Compl or Incmpl
-
*1
No
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Not Avl or Avail
-
*1
No
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Compl or Incmpl
-
*1
No
O2S(A/FS) Monitor
O2S (A/FS) monitor/
Not Avl or Avail
-
*1
No
O2S(A/FS) Monitor
O2S (A/FS) monitor/
Compl or Incmpl
-
*1
No
A/C Monitor
A/C monitor/
Not Avl or Avail
-
*1
No
A/C Monitor
A/C monitor/
Compl or Incmpl
-
*1
No
2nd Air Monitor
2nd air monitor/
Not Avl or Avail
-
*1
No
2nd Air Monitor
2nd air monitor/
Compl or Incmpl
-
*1
No
EVAP Monitor
EVAP monitor/
Not Avl or Avail
-
*1
No
EVAP Monitor
EVAP monitor/
Compl or Incmpl
-
*1
No
Heated Catalyst Monitor
Heated catalyst monitor/
Not Avl or Avail
-
*1
No
Heated Catalyst Monitor
Heated catalyst monitor/
Compl or Incmpl
-
*1
No
Catalyst Monitor
Catalyst monitor/
Not Avl or Avail
-
*1
No
Catalyst Monitor
Catalyst monitor/
Compl or Incmpl
-
*1
No
*1:
Avail: The monitor is available on the vehicle.
Not Avl: The monitor is not available on the vehicle.
Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.
Monitor result (mode 06): The last judgment result is output. This is not cleared when the ignition switch is turned off, but is cleared when DTCs are cleared.

Monitor Information 2 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stored as Freeze Frame Data
Component Monitor ENA
Comprehensive component monitor/
Unable or Enable
-
*2
No
Component Monitor CMPL
Comprehensive component monitor/
Compl or Incmpl
-
*2
No
Fuel System Monitor ENA
Fuel system monitor/
Unable or Enable
-
*2
No
Fuel System Monitor CMPL
Fuel system monitor/
Compl or Incmpl
-
*2
No
Misfire Monitor ENA
Misfire monitor/
Unable or Enable
-
*2
No
Misfire Monitor CMPL
Misfire monitor/
Compl or Incmpl
-
*2
No
EGR/VVT Monitor ENA
EGR monitor/
Unable or Enable
-
*2
No
EGR/VVT Monitor CMPL
EGR monitor/
Compl or Incmpl
-
*2
No
Heater Monitor ENA
O2S (A/FS) heater monitor/
Unable or Enable
-
*2
No
Heater Monitor CMPL
O2S (A/FS) heater monitor/
Compl or Incmpl
-
*2
No
O2S(A/FS) Monitor ENA
O2S (A/FS) monitor/
Unable or Enable
-
*2
No
O2S(A/FS) Monitor CMPL
O2S (A/FS) monitor/
Compl or Incmpl
-
*2
No
A/C Monitor ENA
A/C monitor/
Unable or Enable
-
*2
No
A/C Monitor CMPL
A/C monitor/
Compl or Incmpl
-
*2
No
2nd Air Monitor ENA
2nd air monitor/
Unable or Enable
-
*2
No
2nd Air Monitor CMPL
2nd air monitor/
Compl or Incmpl
-
*2
No
EVAP Monitor ENA
EVAP monitor/
Unable or Enable
-
*2
No
EVAP Monitor CMPL
EVAP monitor/
Compl or Incmpl
-
*2
No
Heated Cat Monitor ENA
Heated catalyst monitor/
Unable or Enable
-
*2
No
Heated Cat Monitor CMPL
Heated catalyst monitor/
Compl or Incmpl
-
*2
No
Catalyst Monitor ENA
Catalyst monitor/
Unable or Enable
-
*2
No
Catalyst Monitor CMPL
Catalyst monitor/
Compl or Incmpl
-
*2
No
*2:
Enable: The monitor is available on the vehicle.
Unable: The monitor is not available on the vehicle.
Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed during the current trip. The item changes back to Incmpl when the ignition switch is turned off.
Monitor result (mode 06): The last judgment result is output. This is not cleared when the ignition switch is turned off, but is cleared when DTCs are cleared. Therefore, only when DTCs are cleared at the beginning of a trip do the system monitor (Monitor Information 2) and monitor result (mode 06) match.

Various Vehicle Conditions 3

TC Terminal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
TC Terminal
TC terminal status/
ON or OFF
-
Yes

# Codes (Include History) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
# Codes (Include History)
Number of codes/
Min.: 0, Max.: 255
0
No

MIL 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
MIL
MIL status/
ON or OFF
-
No

MIL ON Run Distance 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
MIL ON Run Distance
Distance driven with MIL on/
Min.: 0 km, Max.: 65535 km
-
No
Diagnostic Note:
This is the distance driven after a DTC is stored.

Running Time from MIL ON 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Running Time from MIL ON
Running time from MIL ON/
Min.: 0 min, Max.: 65535 min
-
No

Time after DTC Cleared 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Time after DTC Cleared
Time after DTCs cleared/
Min.: 0 min, Max.: 65535 min
Time after DTCs cleared
Yes
Diagnostic Note:
This is the time elapsed after DTCs were cleared. Time elapsed after the ignition switch is turned off is not counted.

Distance from DTC Cleared 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Distance from DTC Cleared
Distance driven after DTCs cleared/
Min.: 0 km, Max.: 65535 km
Distance driven after DTCs cleared
Yes
Diagnostic Note:
This is the distance driven after DTCs were cleared.

Warmup Cycle Cleared DTC 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Warmup Cycle Cleared DTC
Warmup cycles after DTCs cleared/
Min.: 0, Max.: 255
-
Yes
Diagnostic Note:
This is the number of warmup cycles after the DTCs were cleared.
This is the number of times the engine was warmed up* after DTCs were cleared (or after the vehicle left the factory).
*: An engine warmup is defined as the engine coolant temperature rising 20°C (104°F) or more and reaching a temperature of 70°C (158°F) or higher after the engine is started.

Dist Batt Cable Disconnect 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Dist Batt Cable Disconnect
Distance driven after battery cable disconnected/
Min.: 0 km, Max.: 65535 km
Total distance vehicle driven after battery cable disconnected
Yes

IG OFF Elapsed Time 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
IG OFF Elapsed Time
Time after ignition switch off/
Min.: 0 min, Max.: 655350 min
-
Yes

OBD Requirements 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
OBD Requirements
OBD requirement
OBD II (California ARB)
No

Number of Emission DTC 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Number of Emission DTC
Emissions-related DTCs
-
No
Diagnostic Note:
This is the number of emissions-related DTCs.

TC and TE1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
TC and TE1
TC and CG (TE1) terminals of DLC3/
ON or OFF
-
Yes

Misfire

Cylinder #1 Misfire Count to Cylinder #4 Misfire Count 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Cylinder #1 Misfire Count
Cylinder #2 Misfire Count
Cylinder #3 Misfire Count
Cylinder #4 Misfire Count
Misfire count of cylinders 1 to 4/
Min.: 0, Max.: 255
0 to 16
Yes
Diagnostic Note:
This is the misfire count for each individual cylinder.
This counter is incremented by one for each misfire and is cleared every 200 revolutions.
Check this item to help determine the malfunctioning cylinder.

Various Vehicle Conditions 4

Engine Speed (Starter Off) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Speed (Starter Off)
Engine speed when starter off/
Min.: 0 rpm, Max.: 51199 rpm
-
Yes
Diagnostic Note:
This is the engine speed immediately after starting the engine.

Starter Count 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Starter Count
Number of times starter turned on after ignition switch turned to ON/
Min.: 0, Max.: 255
-
Yes
Diagnostic Note:
This is the number of times the starter turned on during the current trip.

Run Dist of Previous Trip 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Run Dist of Previous Trip
Distance driven during previous trip/
Min.: 0 km, Max.: 655.35 km
-
Yes
Diagnostic Note:
Before 5 seconds elapse after starting the engine, which is DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.

HINT:
Run Dist of Previous Trip in freeze frame data which were present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of Data List (real-time measurements), or for freeze frame data which were present when the DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.


Engine Starting Time 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Starting Time
Time elapsed before engine starts/
Min.: 0 ms, Max.: 655350 ms
-
Yes
Diagnostic Note:
This is the time elapsed after the starter turns on until the engine speed reaches 500 rpm.
This value is cleared 5 seconds after the engine is started and the value is displayed as 0 ms.

Previous Trip Coolant Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Previous Trip Coolant Temp
Engine coolant temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
Yes
Diagnostic Note:
Before 120 seconds elapse after starting the engine, this parameter indicates the engine coolant temperature at the end of the previous trip.
After 120 seconds elapse after starting the engine, this parameter indicates the engine coolant temperature during the current trip.

Previous Trip Intake Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Previous Trip Intake Temp
Intake air temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
Yes
Diagnostic Note:
Before 120 seconds elapse after starting the engine, this parameter indicates the intake air temperature at the end of the previous trip.
After 120 seconds elapse after starting the engine, this parameter indicates the intake air temperature during the current trip.

Engine Oil Temperature 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Oil Temperature
Engine oil temperature (estimated temperature)/
Min.: -40°C, Max.: 215°C
-
Yes

Previous Trip Eng Oil Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Previous Trip Eng Oil Temp
Engine oil temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
Yes

Ambient Temp for A/C 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Ambient Temp for A/C
Ambient temperature for A/C/
Min.: -40°C, Max.: 215°C
-
Yes

Previous Trip Ambient Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Previous Trip Ambient Temp
Ambient temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
Yes

Engine Start Hesitation 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Start Hesitation
History of hesitation during engine start/
ON or OFF
-
Yes
Diagnostic Note:
This value changes to ON when the engine speed does not reach 500 rpm during cranking.

Low Rev for Eng Start 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Low Rev for Eng Start
History of low engine speed after engine start/
ON or OFF
-
Yes
Diagnostic Note:
This flag changes to ON when the engine speed drops to 200 rpm or less within approximately 2 seconds of starting the engine.

Fuel Cut Elps Time 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel Cut Elps Time
Time elapsed before engine starts/
Time elapsed after fuel cut/
Min.: 0 sec, Max.: 67107 sec
-
Yes

Engine Oil Temp for Eng Start 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Oil Temp for Eng Start
History of engine oil temperature during engine start/
Min.: -40°C, Max.: 215°C
-
Yes

A/F Learn Value Idle #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value Idle #1
Air fuel ratio learn value of idle area/
Min.: -50%, Max.: 49.6%
-15 to +15%
Yes
Diagnostic Note:
Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher).

A/F Learn Value Idle #1 (Dual) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value Idle #1 (Dual)
Air fuel ratio learn value of idle area/
Min.: -50%, Max.: 49.6%
-15 to +15%
Yes
Diagnostic Note:
Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher).

A/F Learn Value Low #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value Low #1
Air fuel ratio learn value of low load area/
Min.: -50%, Max.: 49.6%
-15 to +15%
Yes
Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).

A/F Learn Value Mid1 #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value Mid1 #1
Air fuel ratio learn value of middle1 load area/
Min.: -50%, Max.: 49.6%
-15 to +15%
Yes
Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts).

A/F Learn Value High #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value High #1
Air fuel ratio learn value of high load area/
Min.: -50%, Max.: 49.6%
-15 to +15%
Yes
Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).

A/F Learn Value Low #1 (Dual) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value Low #1 (Dual)
Air fuel ratio learn value of low load area/
Min.: -50%, Max.: 49.6%
-15 to +15%
Yes
Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).

A/F Learn Value Mid1 #1 (Dual) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value Mid1 #1 (Dual)
Air fuel ratio learn value of middle1 load area/
Min.: -50%, Max.: 49.6%
-15 to +15%
Yes
Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts).

A/F Learn Value High #1 (Dual) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value High #1 (Dual)
Air fuel ratio learn value of high load area/
Min.: -50%, Max.: 49.6%
-15 to +15%
Yes
Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).

A/C Magnetic Clutch Relay 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/C Magnetic Clutch Relay
A/C magnetic clutch relay/
ON or OFF
ON: A/C on
Yes

Electrical Fan Motor 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Electrical Fan Motor
Electric fan motors operation status/
ON or OFF
-
Yes

Electric Cooling Fan Relay #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Electric Cooling Fan Relay #1
Electric cooling fan relay No. 1/
ON or OFF
ON: Cooling fan relay No. 1 ON
Yes

Electric Cooling Fan Relay #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Electric Cooling Fan Relay #2
Electric cooling fan relay No. 2/
ON or OFF
ON: Cooling fan relay No. 2 ON
Yes

Brake Override System 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Brake Override System
Brake override system operation/
ON or OFF
ON: Brake override system ON
Yes

Idle Fuel Cut 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Idle Fuel Cut
Fuel cut at idle/
ON or OFF
ON: Fuel cut operating
Yes
Diagnostic Note:
Idle Fuel Cut = "ON" when the throttle valve is fully closed and the engine speed is high.

FC TAU 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
FC TAU
Fuel cut TAU (fuel cut during very light load)/
ON or OFF
ON: Fuel cut operating
Yes
Diagnostic Note:
This is the fuel cut performed under a very light load to prevent the engine combustion from becoming incomplete.

Immobiliser Fuel Cut 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Immobiliser Fuel Cut
Status of immobiliser fuel cut/
ON or OFF
-
Yes

Immobiliser Fuel Cut History 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Immobiliser Fuel Cut History
Status of the immobiliser fuel cut history/
ON or OFF
-
Yes

Fuel Dilution Estimate 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel Dilution Estimate
Fuel dilution estimate/
Min.: 0 ml, Max.: 1279.9 ml
-
Yes

Compression

Engine Speed of Cyl #1 to #4 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Speed of Cyl #1
Engine Speed of Cyl #2
Engine Speed of Cyl #3
Engine Speed of Cyl #4
Engine speed for cylinder No. 1 to No. 4/
Min.: 0 rpm, Max.: 51199 rpm
-
Yes
Diagnostic Note:
This is output only when Check the Cylinder Compression is performed using the Active Test.
This is the engine speed for each cylinder measured during the engine cranking.
When there is compression loss, the engine speed for that cylinder increases.

HINT:
When multiple cylinders have compression loss, the engine speeds for multiple cylinders increase and it is not possible to determine which cylinders have compression loss. At this time, it is necessary to actually perform a compression measurement.


Av Engine Speed of All Cyl 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Av Engine Speed of All Cyl
Average engine speed for all cylinders/
Min.: 0 rpm, Max.: 51199 rpm
-
No
Diagnostic Note:
This is output only when Check the Cylinder Compression is performed using the Active Test.

Automatic Transmission
Refer to Automatic Transmission System (Click here).

Received MIL from ECT 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Received MIL from ECT
MIL status/
ON or OFF
-
No

Shift Position Sig from ECT 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Shift Position Sig from ECT
Received Shift Position Signal from ECT/
1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th
Same as actual gear ratio
No

SPD (NT) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
SPD (NT)
Input turbine speed (speed sensor NT)/
Min.: 0 rpm, Max.: 12750 rpm
  1. Lock-up ON (After warming up engine): Input turbine speed (NT) equal to engine speed
  2. Lock-up OFF (Idling at P or N position): Input turbine speed (NT) nearly equal to engine speed
No

ECT Lock Up 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ECT Lock Up
ECT lock up status/
ON or OFF
-
No

Shift SW Status (P Range) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Shift SW Status (P Range)
Park/neutral position switch status/
ON or OFF
ON: Shift lever in P
OFF: Shift lever not in P
No

Shift SW Status (R Range) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Shift SW Status (R Range)
Park/neutral position switch status/
ON or OFF
ON: Shift lever in R
OFF: Shift lever not in R
No

Shift SW Status (N Range) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Shift SW Status (N Range)
Park/neutral position switch status/
ON or OFF
ON: Shift lever in N
OFF: Shift lever not in N
No

Sports Mode Selection SW 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Sports Mode Selection SW
Sport mode select switch status/
ON or OFF
ON: Shift lever in M, "+" or "-"
OFF: Shift lever not in M, "+" or "-"
No

Shift SW Status (D Range) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Shift SW Status (D Range)
Park/neutral position switch status/
ON or OFF
ON: Shift lever in D
OFF: Shift lever not in D
No

Spark Timing Retard Request from ECT 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Spark Timing Retard Request from ECT
Status of the spark timing retard request from ECT/
ON or OFF
-
No

Fuel Cut Request from ECT 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel Cut Request from ECT
Status of the fuel cut request from ECT/
ON or OFF
-
No

Torque Down Prohibit Request to ECT 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Torque Down Prohibit Request to ECT
Status of the torque down prohibit request to ECT/
ON or OFF
-
No

Torque Down Request from VSC 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Torque Down Request from VSC
Status of the torque down request from VSC/
ON or OFF
-
Yes

Torque Up Request from VSC 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Torque Up Request from VSC
Status of the torque up request from VSC/
ON or OFF
-
Yes

Torque Down Prohibit Request to VSC 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Torque Down Prohibit Request to VSC
Status of the torque down prohibit request to VSC/
ON or OFF
-
Yes

Torque Up Prohibit Request to VSC 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Torque Up Prohibit Request to VSC
Status of the torque up prohibit request to VSC/
ON or OFF
-
Yes

ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Powertrain / Engine / Active Test.

  7. According to the display on the GTS, perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Injection Volume
    Change injection volume
    Between -12.5% and 24.8%
    1. All injectors are tested at the same time.
    2. This test is possible when the following conditions are met:
      1. Engine speed is 3000 rpm or less.
      2. Engine coolant temperature is 80°C (80°F) or more.
    3. Injection volume can be changed in fine gradations within control range.
    4. Control the Injection Volume enables the checking and graphing of the air fuel ratio sensor and the heated oxygen sensor voltage outputs.
    5. To conduct the test, enter the following menus: Active Test / Control the Injection Volume / AFS Voltage B1S1 and O2S B1S2.
    6. During the Active Test, air fuel ratio feedback control and feedback learning are stopped.
    Control the Injection Volume for A/F Sensor
    Change injection volume
    -12%/0%/12%
    1. All injectors are tested at the same time.
    2. This test is possible when the following conditions are met:
      1. Engine speed is 3000 rpm or less.
      2. Engine coolant temperature is 80°C (80°F) or more.
    3. Control the Injection Volume for A/F Sensor enables the checking and graphing of the air fuel ratio sensor and the heated oxygen sensor voltage outputs.
    4. To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor
    5. During the Active Test, air fuel ratio feedback control and feedback learning are stopped.
    Activate the VSV for Evap Control
    Activate purge VSV control
    ON/OFF
    Perform this test when the following conditions are met:
    1. Engine is stopped.
    2. Engine coolant temperature is 80°C (80°F) or more.
    3. Clear DTC after this test finished.
    Control the A/C Magnet Clutch
    A/C magnet clutch control
    ON/OFF
    Perform this test when the following conditions are met:
    1. Ignition switch is ON.
    2. Engine is stopped.
    3. Shift lever is in P, N or neutral.
    Control the Fuel Pump / Speed
    Activate fuel pump
    ON/OFF
    Perform this test when the following conditions are met:
    1. Ignition switch is ON.
    2. Engine is stopped.
    3. Shift lever is in P, N or neutral.
    Control the Fuel Pump Duty
    Fuel pump control
    25%/80%
    Perform this test when the following conditions are met:
    1. Ignition switch is ON.
    2. Engine is stopped.
    3. Shift lever is in P, N or neutral.
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 are connected.
    2. OFF: TC and TE1 are disconnected.
    3. Perform this test when the following conditions are met:
      1. Ignition switch is ON.
      2. Engine is stopped.
      3. Shift lever is in P, N or neutral.
    Control the Electric Cooling Fan
    Control electric cooling fan
    ON/OFF
    Perform this test when the ignition switch is ON.
    Activate the ACC Cut Relay
    Activate ACC cut relay
    ON/OFF
    Perform this test when the following conditions are met:
    1. Ignition switch is ON.
    2. Engine is stopped.
    3. Shift lever is in P, N or neutral.
    Control the ETCS Open/Close Slow Speed
    Throttle actuator
    Close/Open
    This test is possible when the following conditions are met:
    1. Ignition switch is ON.
    2. Engine is stopped.
    3. Accelerator pedal is fully depressed.
    4. Shift lever is in P, N or neutral.
    Control the ETCS Open/Close Fast Speed
    Throttle actuator
    Close/Open
    1. Same as above.
    Control the Injection Timing #1
    Control injection timing #1
    Between -16 deg(CA) and 15.87 deg(CA)
    Perform this test when the following conditions are met:
    1. Engine is idling.
    2. Shift lever is in P, N or neutral.
    Control the Injection Timing #2
    Control injection timing #2
    Between -16 deg(CA) and 15.87 deg(CA)
    Perform this test when the following conditions are met:
    1. Engine is idling.
    2. Shift lever is in P, N or neutral.
    Control the Injection Timing #3
    Control injection timing #3
    Between -16 deg(CA) and 15.87 deg(CA)
    Perform this test when the following conditions are met:
    1. Engine is idling.
    2. Shift lever is in P, N or neutral.
    Control the Injection Timing #4
    Control injection timing #4
    Between -16 deg(CA) and 15.87 deg(CA)
    Perform this test when the following conditions are met:
    1. Engine is idling.
    2. Shift lever is in P, N or neutral.
    Activate the Vacuum Pump
    Activate leak detection pump (built into canister pump module)
    ON/OFF
    Perform this test when the Evaporative System Check is not performed.
    Activate the VSV for Vent Valve
    Activate vent valve (built into canister pump module)
    ON/OFF
    Perform this test when the Evaporative System Check is not performed.
    Control the Target Fuel Pressure
    Control the target fuel pressure
    -12.5 to 24.8%
    Perform the test at below 3000 rpm.
    Control the Voltage of Alternator
    Control the voltage of alternator
    12.8 to 14.3 V
    Perform this test when the following conditions are met:
    1. Engine is idling.
    2. Shift lever is in P, N or neutral.
    Control the Injection Way
    Perform 3 pattern in order to operate fuel injection
    Either/Port/Direct
    This test is possible when the following conditions are met:
    1. Engine is idling.
    2. Engine coolant temperature is 80°C (176°F ) or more.
    3. Data List / Injection Switching Status is OK.
    Perform the port mode within 3 minutes.
    D-4S (A/F Control)
    Perform 3 pattern in order to operate air fuel ratio control
    1. Either/Port/Direct
    2. -12.5 to 24.8%
    This test is possible when the following conditions are met:
    1. Engine speed is 3000 rpm or less
    2. Engine coolant temperature is 80°C (176°F ) or more.
    3. Shift lever is in P, N or neutral.
    Perform the port mode within 3 minutes.
    D-4S (Fuel Cut)
    Perform 3 pattern in order to operate fuel cut
    1. Either/Port/Direct
    2. Selected cylinder (cylinder #1 to #4)
    This test is possible when the following conditions are met:
    1. Engine speed is 3000 rpm or less
    2. Engine coolant temperature is 80°C (176°F ) or more.
    3. Shift lever is in P, N or neutral.
    Perform the port mode within 3 minutes.
    D-4S (Injection Volume)
    Perform 3 pattern in order to operate injection volume
    1. Either/Port/Direct
    2. -12.5 to 24.8%
    This test is possible when the following conditions are met:
    1. Engine speed is 3000 rpm or less
    2. Engine coolant temperature is 80°C (176°F ) or more.
    3. Shift lever is in P, N or neutral.
    Perform the port mode within 3 minutes.
    Control the Select Cylinder Fuel Cut
    Selected cylinder (cylinder #1 to #4) injector fuel cut
    #1/#2/#3/#4
    ON/OFF
    This test is possible when the following conditions are met
    1. Vehicle is stopped.
    2. Engine is idling.
    3. Shift lever is in P, N or neutral.
    4. Speed sensor is normal.
    *1
    Control the All Cylinders Fuel Cut
    All cylinder fuel cut
    ON/OFF
    This test is possible when the following conditions are met
    1. Vehicle is stopped.
    2. Engine is idling.
    3. Shift lever is in P, N or neutral.
    4. Speed sensor is normal.
    *1
    Check the Cylinder Compression
    Check the cylinder compression pressure
    ON/OFF
    This test is possible when the following conditions are met
    1. Vehicle is stopped.
    2. Engine is idling.
    3. Shift lever is in P, N or neutral.
    4. Speed sensor is normal.
    *1
    Fuel injection and ignition stop in all cylinders.
    *2
    Activate the Starter Cut Relay
    Activate starter cut relay
    ON/OFF
    Perform this test when the following conditions are met:
    1. Ignition switch is ON.
    2. Engine is stopped.
    3. Shift lever is in P, N or neutral.
    Control the Target Engine Speed
    Control the target engine speed
    500 to 2000 rpm
    Test possible during vehicle stopping and engine idling.
    Control the VVT Linear (Bank 1)
    Control VVT (for intake side of bank 1)
    -27 to 36 deg (CA)
    1. Engine stalls or idles roughly when the VVT actuator is operated.
    2. Perform this test when the following conditions are met:
      1. Vehicle is stopped.
      2. Engine is idling.
      3. Engine coolant temperature is 80°C (176°F ) or more.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT Linear (Bank 2)
    Control VVT (for intake side of bank 2)
    -27 to 36 deg (CA)
    1. Engine stalls or idles roughly when the VVT actuator is operated.
    2. Perform this test when the following conditions are met:
      1. Engine is idling.
      2. Engine coolant temperature is 80°C (176°F ) or more.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT Exhaust Linear (Bank 1)
    Control VVT (for exhaust side of bank 1)
    0 to 51 deg (CA)
    1. Engine stalls or idles roughly when the VVT actuator is operated.
    2. Perform this test when the following conditions are met:
      1. Vehicle is stopped.
      2. Engine is idling.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT Exhaust Linear (Bank 2)
    Control VVT (for exhaust side of bank 2)
    0 to 51 deg (CA)
    1. Engine stalls or idles roughly when the VVT actuator is operated.
    2. Perform this test when the following conditions are met:
      1. Vehicle is stopped.
      2. Engine is idling.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.

    NOTICE:
    *1:
    1. If the display of the Data List item Catalyst OT MF F/C item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling.
    2. If the display of the Data List item Catalyst OT MF F/C item is Avail, perform this Active Test as described below.
      1. Stop the engine, turn the ignition switch to ON.
      2. Enter the Control the Select Cylinder Fuel Cut.
      3. Select the cylinder for fuel cut (cylinder #1 to #4) and turn the Active Test ON (press the RIGHT or LEFT button).
      4. Start the engine.

    HINT:
    *2: When cranking the engine, each cylinder measures the engine speed. In this Active Test, the fuel and ignition of all cylinders is cut. The engine must then be cranked for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.

    1. Warm up the engine.
    2. Turn the ignition switch off.
    3. Connect the GTS to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the GTS on.
    6. Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression.

      HINT:
      To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.

    7. Push the snapshot button to turn the snapshot function on.

      HINT:
      Using the snapshot function, data can be recorded during the Active Test.

    8. While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

      HINT:
      After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.

    9. Crank the engine for about 10 seconds.

      HINT:
      Continue to crank the engine until the values change from the default value (51199 rpm).

    10. Monitor the engine speed (Engine Speed of Cyl #1 to #4) displayed on the GTS.

      HINT:
      At first, the GTS displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.

      NOTICE:
      1. Do not crank the engine continuously for 20 seconds or more.
      2. If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.
      3. Use a fully-charged battery.


SYSTEM CHECK

HINT:
Performing a System Check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are stored, and can detect potential malfunctions in the system. The System Check can be performed with the GTS.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Powertrain / Engine / Utility.

  5. Perform the System Check by referring to the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Evaporative System Check
    (Automatic Mode)
    Perform 5 steps in order to operate EVAP key-off monitor automatically
    35°C (95°F) or less
    1. If no pending DTCs are output after performing this test, the system is functioning normally.
    2. Refer to EVAP Inspection Procedure (Click here).
    Evaporative System Check
    (Manual Mode)
    Perform 5 steps in order to operate EVAP key-off monitor manually
    35°C (95°F) or less
    1. Used to detect malfunctioning parts.
    2. Refer to EVAP Inspection Procedure (Click here).