Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for Front Side)

SIDE AIRBAG SENSOR (for Front Side) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. INSTALL DOOR SIDE AIRBAG SENSOR
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    The power window system utilizes a mechanism that the door glass moves down slightly when the door is opened, and that the glass moves up when closing the door in order to prevent the door molding from being damaged. When the battery negative (-) terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



    B311396
  1. Connect the connector to the door side airbag sensor.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.


    1. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

  1. Insert the pin (stopper) into the door hole and install the door side airbag sensor to the front door panel with the nut.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    NOTICE:
    1. If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
    3. Make sure that the pin (stopper) is securely inserted into the body hole.
    4. Tighten the nut while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

  1. Check that there is no looseness in the installation parts of the door side airbag sensor.



2. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the front door panel.



  1. Pass the front door lock remote control cable assembly and the front door inside locking cable assembly through a new front door service hole cover.


    B314821E01


    Text in Illustration 
    *1
    Reference Point
    -
    -

  1. Attach the front door service hole cover according to the reference points on the front door panel.

    NOTICE:
    1. Overlay the butyl tape in lengths of 20 cm (7.874 in.) or more.
    2. Do not block the drip holes in the front door panel with butyl tape.
    3. Securely install the front door service hole cover preventing wrinkles and air bubbles.

  1. Connect each connector.



3. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B313122E01
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable Assembly
    *2
    Front Door Lock Remote Control Cable Assembly

  1. Connect each connector.



    B314824
  1. Engage the 10 clips and install the front door trim board sub-assembly.



    B313120
  1. Engage the clip and install the 3 screws.



    B314825
  1. Engage the claw and install the cap.



4. INSTALL DOOR ARMREST COVER


    B314960
  1. Engage the guide and 7 claws, and install the door armrest cover.



5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



6. PERFORM DIAGNOSTIC SYSTEM CHECK
(Click here)


7. INSPECT SRS WARNING LIGHT
(Click here)


8. INITIALIZE POWER WINDOW CONTROL SYSTEM
(Click here)


9. INSPECT POWER WINDOW OPERATION
(Click here)