Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (NETWORK GATEWAY ECU)

B311498E01


Text in Illustration 
*1
Instrument Panel Junction Block Assembly
*2
Main Body ECU (Network Gateway ECU)
  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly (Click here).

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-1 (BECU) - Body ground
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    MB-8 (IG) - Body ground
    None - Body ground
    Engine switch power supply
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    MB-9 (ACC) - Body ground
    None - Body ground
    ACC power supply
    Engine switch on (ACC)
    11 to 14 V
    Engine switch off
    Below 1 V
    MB-11 (GND) - Body ground
    None - Body ground
    Ground
    Always
    Below 1 Ω
    MB-32 (BMPX) - Body ground
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    D6-1 (GND) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    A73-4 (GND) - Body ground
    B-Y - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Install the main body ECU (network gateway ECU) to the instrument panel junction block assembly (Click here).

  4. Measure the voltage and waveform according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3A-28 - Body ground
    V - Body ground
    Driver side door courtesy light switch input
    Driver side door open
    Below 1 V
    Driver side door closed
    11 to 14 V
    3B-13 - Body ground
    GR - Body ground
    Passenger side door courtesy light switch input
    Passenger side door open
    Below 1 V
    Passenger side door closed
    11 to 14 V
    3B-22 - Body ground
    V - Body ground
    Security indicator light signal
    Security indicator light illuminated (illuminates only for 60 seconds in alarm sounding state (blinks when system in armed state))
    Below 4 V
    3D-26 - Body ground
    SB - Body ground
    Luggage compartment door courtesy light switch input
    Luggage compartment door open
    Below 1 V
    Engine switch off, all doors closed and luggage compartment door closed
    11 to 14 V
    3D-31 - Body ground
    BR - Body ground
    Vehicle horn signal
    Vehicle horns sounding (Theft deterrent system is in alarm sounding state)
    Pulse generation
    Vehicle horns not sounding (Theft deterrent system is in armed state)
    11 to 14 V
    3B-2 - Body ground
    V - Body ground
    Door lock motor lock drive output (for driver side)
    Driver side door control switch not pushed
    Below 1 V
    Lock side of driver side door control switch pushed
    11 to 14 V
    3B-3 - Body ground
    L - Body ground
    Door lock motor lock drive output (for passenger side)
    Driver side door control switch not pushed
    Below 1 V
    Lock side of driver side door control switch pushed
    11 to 14 V
    3B-1 - Body ground
    R-G - Body ground
    Door lock motor unlock drive output (for driver side)
    Driver side door control switch not pushed
    Below 1 V
    Unlock side of driver side door control switch pushed
    11 to 14 V
    3B-4 - Body ground
    L-W - Body ground
    Door lock motor unlock drive output (for passenger side)
    Driver side door control switch not pushed
    Below 1 V
    Unlock side of driver side door control switch pushed
    11 to 14 V
    D5-22 (ACC) - Body ground
    W - Body ground
    ACC power supply
    Engine switch on (ACC)
    11 to 14 V
    Engine switch off
    Below 1 V
    D6-11 (LSFD) - Body ground
    W - Body ground
    Driver side door unlock detection switch input
    Driver side door unlocked
    Below 1 V
    Engine switch off, all doors closed and driver side door locked
    Pulse generation (See waveform 1 or 2)
    D6-12 (LSFP) - Body ground
    SB - Body ground
    Passenger side door unlock detection switch input
    Passenger side door unlocked
    Below 1 V
    Engine switch off, all doors closed and passenger side door locked
    Pulse generation (See waveform 1 or 2)



  5. Inspect using an oscilloscope.

    NOTICE:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      B199631E01
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      D6-11 (LSFD) - Body ground
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Engine switch off, all doors closed and driver side door locked
      Measurement Condition 
      Item
      Content
      Tester Connection
      D6-12 (LSFP) - Body ground
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Engine switch off, all doors closed and passenger side door locked



    2. B199632E04
    3. Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      D6-11 (LSFD) - Body ground
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Engine switch off, all doors closed and driver side door locked
      Measurement Condition 
      Item
      Content
      Tester Connection
      D6-12 (LSFP) - Body ground
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Engine switch off, all doors closed and passenger side door locked