Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

DTC    P0604    Internal Control Module Random Access Memory (RAM) Error

DTC    P0605    Internal Control Module Read Only Memory (ROM) Error

DTC    P0606    ECM / PCM Processor

DTC    P060A    Internal Control Module Monitoring Processor Performance

DTC    P060B    Internal Control Module A/D Processing Performance

DTC    P062F    Internal Control Module EEPROM Error

for Preparation Click here


DESCRIPTION

  1. P0604
    The ECM continuously monitors its internal memory status. This self-check ensures that the ECM functioning properly. It is diagnosed by internal "mirroring" of the main CPU and sub CPU to detect the Random Access Memory (RAM) errors. If outputs from these CPUs are different and deviate from the standard, the ECM stores the DTC.
  1. P0605
    The ECM continuously monitors its internal memory status. This self-check ensures that the ECM functioning properly. It is diagnosed by internal "mirroring" of the main CPU and sub CPU to detect the Read Only Memory (ROM) errors. If outputs from these CPUs are different and deviate from the standard, the ECM stores the DTC.
  1. P0606
    The ECM continuously monitors its main and sub CPUs. This self-check ensures that the ECM is functioning properly. If outputs from the CPUs are different and deviate from the standard, the ECM stores the DTC.
  1. P060A
    The main CPU and sub CPU of the ECM perform data communication between each other. The main CPU monitors the communications and WDC pulses from the sub CPU. If the malfunction is detected, the ECM stores the DTC.
  1. P060B
    If a communication error occurs in the ECM, the ECM stores the DTC.
  1. P062F
    The ECM monitors its internal operation. If the ECM detects an internal malfunction, the ECM stores the DTC.

DTC
DTC Setting Condition
Trouble Area
P0604
ECM internal error (RAM)
(1 trip detection logic)
ECM
P0605
ECM internal error (ROM)
(1 trip detection logic)
ECM
P0606
ECM internal error (Processor)
(1 trip detection logic)
ECM
P060A
ECM internal error (Monitoring processor)
(1 trip detection logic)
ECM
P060B
ECM internal error (A/D processor)
(1 trip detection logic)
ECM
P062F
ECM internal error (EEPROM)
(1 trip detection logic)
ECM

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  4. Turn the GTS off.
  5. Turn the ignition switch off.
  6. Disconnect the GTS.
  7. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
  8. Connect the cable to the negative (-) battery terminal.
  9. Connect the GTS to the DLC3.
  10. Turn the ignition switch to ON and turn the GTS on.
  11. Wait 16 seconds or more.
  12. Enter the following menus: Powertrain / Engine / Trouble Codes.
  13. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  15. Input the DTC: P0604, P0605, P0606, P060A, P060B or P062F.
  16. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  17. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.READ DTC OUTPUT (DTC P0604, P0605, P0606, P060A, P060B AND/OR P062F)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the GTS off.

  1. Disconnect the GTS.

  1. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Wait for 16 seconds or more.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC is not output
    A
    DTC DTC P0604, P0605, P0606, P060A, P060B or P062F is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)