Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT

REAR WHEEL ALIGNMENT > ADJUSTMENT

for Preparation Click here


NOTICE:
If the wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:
Perform zero point calibration of the yaw rate and acceleration sensor and test mode inspection (Click here).



1. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold Tire Inflation Pressure:

    Tire Size
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    205/55R16 91V
    240 (2.4, 35)
    240 (2.4, 35)
    215/45R17 87W
    240 (2.4, 35)
    240 (2.4, 35)
    T135/80D 16 101M
    420 (4.2, 60)
    420 (4.2, 60)



    C265375
  1. Using a dial indicator, check the runout of the wheel.
    Maximum wheel runout 
    Steel wheel
    2.0 mm (0.0787 in.) (Vertical and lateral)
    Aluminum wheel
    1.0 mm (0.0394 in.) (Vertical and lateral)



2. MEASURE VEHICLE HEIGHT


    C257522E01
  1. Bounce the vehicle up and down at the corners to stabilize the suspension before inspecting the vehicle height.
    Vehicle Height (Unloaded Vehicle) 
    Tire Size
    Front B - A
    Rear C
    Front D
    Rear E
    205/55 R16
    146 mm
    (5.75 in.)
    225 mm
    (8.86 in.)
    375 mm
    (14.76 in.)
    372 mm
    (14.65 in.)
    215/45 R17
    146 mm
    (5.75 in.)
    225 mm
    (8.86 in.)
    375 mm
    (14.76 in.)
    372 mm
    (14.65 in.)

    NOTICE:
    1. Perform the inspection while the vehicle is empty (with a spare tire, jack and tools on board, and with the fuel tank filled with fuel).
    2. The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.

    Measuring points:
    A:
    Ground clearance of front lower suspension arm set front bolt center
    B:
    Ground clearance of front wheel center
    C:
    Ground clearance of lower control arm set bolt center
    D:
    Front wheel arch height of front wheel center
    E:
    Rear wheel arch height of rear wheel center



3. INSPECT TOE-IN

NOTICE:
Inspect while the vehicle is unloaded.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  1. Release the parking brake and move the shift lever to N.

  1. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step B)



    C188968E06
  1. Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).
    Text in Illustration 
    *a
    Tread Center Mark
    *b
    Dimension B
    V100135
    Front of the Vehicle

  1. Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

    HINT:
    Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step B again.



    C188969E06
  1. Measure the distance between the tread center marks on the front of the rear wheels (dimension A).
    Text in Illustration 
    *a
    Dimension A
    V100135
    Front of the Vehicle

    Toe-in (Unloaded Vehicle):
    Specified Condition
    C + D: 0°10' +/- 0°15' (0.16° +/- 0.24°)
    B - A: 2.0 +/- 3.0 mm(0.0787 +/- 0.1181 in.)

    HINT:
    Measure "B - A" only when "C + D" cannot be measured.

    If the toe-in is not within the specified range, adjust it at the toe control link sub-assembly.



4. ADJUST TOE-IN


    C266980
  1. Loosen the toe adjust cam nut.

  1. Turn the adjust cams by an equal amount to adjust the toe-in.

    Toe-in (Unloaded Vehicle):
    Specified Condition
    C + D: 0°10' +/- 0°15' (0.16° +/- 0.24°)
    B - A: 2.0 +/- 3.0 mm(0.0787 +/- 0.1181 in.)

    HINT:
    1. Try to adjust the toe-in to the center value.
    2. The toe-in will change by approximately 5.2 mm (0.205 in.) for each gradation of the cam.

  1. Tighten the toe adjust cam nut.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }



5. INSPECT CAMBER
  1. Remove the center wheel ornament.



    C107736E07
  1. Install a camber-caster-kingpin gauge at the center of the axle hub or drive shaft.
    Text in Illustration 
    *1
    Camber-caster-kingpin Gauge

  1. Inspect the camber.

    Camber (Unloaded Vehicle):
    Camber Inclination
    Right-left Difference
    -1°12' +/- 45'
    (-1.20° +/- 0.75°)
    45' (0.75°) or less

    If the measured value is not within the specified range, inspect the suspension parts for damage and wear. Replace parts as necessary because camber cannot be properly adjusted with any damaged or worn parts.

  1. Remove the camber-caster-kingpin gauge.

  1. Install the center wheel ornament.



6. INSPECT REAR SUSPENSION


    C257519
  1. Inspect the rear suspension member.

    1. Measure the distance between the centers of the 2 installation bolts of the rear No. 2 suspension arm assembly LH and RH

      Standard distance:
      454.5 to 460.5 mm (17.89 to 18.13 in.)

      If the distance is not within the specified range, replace the rear suspension member.



    C257520
  1. Inspect the rear No. 2 suspension arm assembly.

    1. Measure the distance between the centers of the 2 installation bolts of the rear No. 2 suspension arm assembly.

      Standard distance:
      448.9 to 452.9 mm (17.67 to 17.83 in.)

      If the distance is not within the specified range, replace the rear No. 2 suspension arm assembly.

  1. Inspect and adjust the toe-in and camber.

    1. Inspect the toe-in and camber.
      Inspect the toe-in and camber. If the values are not within the specified ranges, adjust the installation bolt holding the rear suspension member to the vehicle body, or the bolt holding the upper control arm and rear suspension arm so that the values fall within the specified ranges.



7. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


8. VSC SENSOR NEUTRAL MEMORIZATION
(Click here)


9. HEIGHT CONTROL SENSOR SIGNAL INITIALIZE (w/ HID Headlight System)
(Click here)


10. ADJUST HEADLIGHT AIMING (w/ HID Headlight System)
(Click here)