Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)

DTC    B2274    ACC Monitor Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit between the ACC output terminal of the certification ECU (smart key ECU assembly) and the ACC relay is detected.

HINT:
When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.


DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2274
Malfunction in the ACC relay activation circuit in the certification ECU (smart key ECU assembly) or the external circuit (1-trip detection logic*1).

HINT:
When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.

  1. AM2 No. 2 fuse
  2. Instrument panel junction block assembly (ACC relay)
  3. Certification ECU (smart key ECU assembly)
  4. Wire harness or connector
Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off.

HINT:
To turn the engine switch on (ACC), carry the key and press the engine switch with the shift lever in P or N*2 and the brake pedal*2 or clutch pedal*3 released.

  1. *1: Only output while a malfunction is present and the engine switch is on (IG)
  2. *2: for Automatic Transmission
  3. *3: for Manual Transmission

Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
  1. If there is a malfunction when the relay is stuck on, the ACC relay does not turn off even though all the power is off.
  2. If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the engine switch is on (ACC).

HINT:
The engine switch can be turned on (IG) and the engine can be started.

-

Related Data List and Active Test Items 
DTC No.
Data List Item
Active Test Item
B2274
Power Source Control
  1. ACC Relay Monitor
Engine
  1. Ignition Status
-

WIRING DIAGRAM


B312726E01


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
  2. The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (Click here).
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (Click here).
  4. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
  5. Inspect the fuses of circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B268625E18
  1. Disconnect the D48 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D48-2 (+B) - Body ground
    Always
    9.5 to 16 V

    Text in Illustration 
    *a
    Rear view of harness connected
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


2.CHECK HARNESS AND CONNECTOR (GROUND)
B268625E19
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of harness connected
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU)
  1. Disconnect the D41 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the 3A instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D41-4 (ACCD) - 3A-20
    Always
    Below 1 Ω
    3A-12 - Body ground
    Always
    Below 1 Ω
    D41-4 (ACCD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC1, ACC2 RELAY)
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    B312727E01


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3E-1 - 3B-28
    When battery voltage absent
    10 kΩ or higher
    When battery voltage is applied to terminals 3A-20 and 3A-12
    Below 1 Ω
    3E-1 - 3A-10
    When battery voltage absent
    10 kΩ or higher
    When battery voltage is applied to terminals 3A-20 and 3A-12
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B268626E07
  1. Install the main body ECU (network gateway ECU) to the instrument panel junction block assembly (Click here).

  1. Install the instrument panel junction block assembly.

  1. Reconnect the D41 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-4 (ACCD) - Body ground
    Engine switch off → Engine switch on (ACC)
    Below 1 V → 8.5 V or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

USE SIMULATION METHOD TO CHECK (Click here)