DTC B1805 Short in P Squib Circuit |
DTC B1806 Open in P Squib Circuit |
DTC B1807 Short in P Squib Circuit (to Ground) |
DTC B1808 Short in P Squib Circuit (to +B) |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1805 |
|
|
| B1806 |
| |
| B1807 |
| |
| B1808 |
|

| 1.CHECK CONNECTORS |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the instrument panel passenger airbag assembly and airbag ECU assembly.
Disconnect the connectors from the instrument panel passenger airbag assembly and airbag ECU assembly.
Check that the terminals of the connectors are not damaged.
Check that the short spring for the instrument panel wire with the activation prevention mechanism is not deformed or damaged.
| *1 | Instrument Panel Passenger Airbag Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
|
| ||||
| OK | |
| 2.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB) |
Connect the connector to the airbag ECU assembly.

| *A | w/o Dual Airbag | *B | w/ Dual Airbag |
| *1 | Instrument Panel Passenger Airbag Assembly | *2 | Airbag ECU Assembly |
| *a | Front view of wire harness connector (to Instrument Panel Passenger Airbag Assembly) | - | - |
Connect SST (resistance 2.1 Ω) to connector C.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect SST from connector C.
|
| ||||
| OK | ||
| ||
| 3.CHECK INSTRUMENT PANEL WIRE |
![]() |
Disconnect the instrument panel wire from the airbag ECU assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D30-2 (P+) - Body ground | Ignition switch ON | Below 1 V |
| D30-3 (P-) - Body ground | Ignition switch ON | Below 1 V |
| Tester Connection | Condition | Specified Condition |
| D30-2 (P+) - Body ground | Ignition switch ON | Below 1 V |
| D30-1 (P-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D30-2 (P+) - D30-3 (P-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D30-2 (P+) - D30-1 (P-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D30-2 (P+) - Body ground | Always | 1 MΩ or higher |
| D30-3 (P-) - Body ground | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
| D30-2 (P+) - Body ground | Always | 1 MΩ or higher |
| D30-1 (P-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D30-2 (P+) - D30-3 (P-) | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
| D30-2 (P+) - D30-1 (P-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| *1 | Instrument Panel Passenger Airbag Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector (to Instrument Panel Passenger Airbag Assembly) |
|
| ||||
| OK | |
| 4.CHECK DTC |
![]() |
Connect the connectors to the instrument panel passenger airbag assembly and airbag ECU assembly.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Instrument Panel Passenger Airbag Assembly |
| *2 | Airbag ECU Assembly |
|
| ||||
| OK | ||
| ||