Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1815    Short in P Squib (Dual Stage - 2nd Step) Circuit

DTC    B1816    Open in P Squib (Dual Stage - 2nd Step) Circuit

DTC    B1817    Short in P Squib (Dual Stage - 2nd Step) Circuit (to Ground)

DTC    B1818    Short in P Squib (Dual Stage - 2nd Step) Circuit (to +B)

for Preparation Click here


DESCRIPTION

The front passenger side squib 2nd step circuit consists of the airbag ECU assembly and instrument panel passenger airbag assembly.
The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front passenger side squib 2nd step circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1815
  1. The airbag ECU assembly receives a line short circuit signal in the front passenger side squib 2nd step circuit during primary check.
  2. Front passenger side squib 2nd step malfunction
  3. Airbag ECU assembly malfunction
  1. Instrument panel wire
  2. Instrument panel passenger airbag assembly (Front passenger side squib 2nd step)
  3. Airbag ECU assembly
B1816
  1. The airbag ECU assembly receives an open circuit signal in the front passenger side squib 2nd step circuit.
  2. Front passenger side squib 2nd step malfunction
  3. Airbag ECU assembly malfunction
B1817
  1. The airbag ECU assembly receives a short circuit to ground signal in the front passenger side squib 2nd step circuit.
  2. Front passenger side squib 2nd step malfunction
  3. Airbag ECU assembly malfunction
B1818
  1. The airbag ECU assembly receives a short circuit to B+ signal in the front passenger side squib 2nd step circuit.
  2. Front passenger side squib 2nd step malfunction
  3. Airbag ECU assembly malfunction

WIRING DIAGRAM


C263726E02


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

HINT:
  1. Perform the simulation method by selecting check mode (Signal Check) using the GTS (Click here).
  2. After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (Click here).

1.CHECK CONNECTORS
C263727E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the instrument panel passenger airbag assembly and airbag ECU assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the instrument panel passenger airbag assembly and airbag ECU assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the short spring for the instrument panel wire with the activation prevention mechanism are not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.

    Text in Illustration 
    *1
    Instrument Panel Passenger Airbag Assembly
    *2
    Airbag ECU Assembly
    *3
    Instrument Panel Wire



NG
REPLACE INSTRUMENT PANEL WIRE
OK


2.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB 2ND STEP)


    C266284E01
  1. Connect the connector to the airbag ECU assembly.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the instrument panel passenger airbag assembly (front passenger side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting it.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1815, B1816, B1817 or B1818 is not output.

    HINT:
    Codes other than DTCs B1815, B1816, B1817 and B1818 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Disconnect SST from connector C.
    Text in Illustration 
    *1
    Instrument Panel Passenger Airbag Assembly
    *2
    Airbag ECU Assembly
    *a
    Front view of wire harness connector
    (to Instrument Panel Passenger Airbag Assembly)



NG
Go to step 3
OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (Click here)  

3.CHECK FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT


    C261678E01
  1. Disconnect the instrument panel wire from the airbag ECU assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      D30-4 (P2+) - Body ground
      Ignition switch ON
      Below 1 V
      D30-3 (P2-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check for an open in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D30-4 (P2+) - D30-3 (P2-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D30-4 (P2+) - Body ground
      Always
      1 MΩ or higher
      D30-3 (P2-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D30-4 (P2+) - D30-3 (P2-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.
      Text in Illustration 
      *1
      Instrument Panel Passenger Airbag Assembly
      *2
      Airbag ECU Assembly
      *3
      Instrument Panel Wire
      *a
      Front view of wire harness connector
      (to Instrument Panel Passenger Airbag Assembly)



NG
REPLACE INSTRUMENT PANEL WIRE
OK


4.CHECK DTC


    C260971E01
  1. Connect the connectors to the instrument panel passenger airbag assembly and airbag ECU assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1815, B1816, B1817 or B1818 is not output.

    HINT:
    Codes other than DTCs B1815, B1816, B1817 and B1818 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Instrument Panel Passenger Airbag Assembly
    *2
    Airbag ECU Assembly



NG
REPLACE AIRBAG ECU ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)