Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1241    Low or High Power Supply Voltage

for Preparation Click here


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.
This DTC is stored when the +BS terminal voltage meets one of the DTC detection conditions due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc.
The DTC is canceled when the +BS terminal voltage returns to normal.

DTC No.
DTC Detection Condition
Trouble Area
C1241
Any of the following is detected:
  1. The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (soft low voltage) is 9.6 V or less for 1 second or more.
  2. The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (hard low voltage) is 6.9 V or less for 1 second or more.
  3. The vehicle speed is 15 km/h (9 mph) or more, the +BS terminal voltage is 9.6 V or more, the skid control ECU (brake actuator assembly) turns on more than one valve at the same time within a short period of time and the valve relay supply voltage drop exceeds the threshold.*
  1. ABS NO. 2 fuse
  2. ECU IG1 fuse
  3. Battery
  4. Charging system
  5. Power source circuit
  6. Ground circuit
  7. Internal power supply circuit of the skid control ECU (brake actuator assembly)
*: The skid control ECU (brake actuator assembly) monitors the resistance of the power source line at the +BS terminal. A malfunction is detected when an abnormality occurs in the +BS terminal wire harness or its connection and the skid control ECU (brake actuator assembly) determines that the wiring resistance at the +BS terminal exceeds the standard resistance.

WIRING DIAGRAM


C261860E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK BATTERY
  1. Check the battery voltage.

    Standard Voltage:
    11 to 14 V



NG
CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C261861E07
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A5-25 (+BS) - Body ground
    Always
    11 to 14 V
    A5-25 (+BS) - A5-38 (GND1)
    Always
    11 to 14 V
    A5-28 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V
    A5-28 (IG1) - A5-38 (GND1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))

    Result:

    Result
    Proceed to
    OK
    A
    NG (for +BS circuit)
    B
    NG (for IG1 circuit)
    C



B
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
A


3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)


    C261861E06
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A5-38 (GND1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


4.RECONFIRM DTC
  1. Reconnect the skid control ECU (brake actuator assembly) connector.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Perform a road test.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1241 is not output.
    A
    DTC C1241 is output.
    B

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)