Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)

DTC    B2285    Steering Lock Position Signal Circuit Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when the steering lock position signal sent by the steering lock actuator assembly (steering lock ECU) via direct line and the steering lock position signal sent via LIN communication do not match.

HINT:
When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.


DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2285
The steering lock position signal sent by the steering lock ECU via direct line and the steering lock position signal sent via LIN communication (1-trip detection logic*) do not match.
  1. AM2 No. 2 fuse
  2. Steering lock actuator assembly (steering lock ECU)
  3. Certification ECU (smart key ECU assembly)
  4. Wire harness or connector
Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and reconnect the cable to the negative (-) battery terminal. Wait another 40 seconds or more with the engine switch off (steering locked), and then turn the engine switch on (ACC) (steering unlocked) and wait 40 seconds or more.
*: Only output while a malfunction is present and the engine switch is on (IG)

Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
The engine cannot be started.
An engine start command is not output.

Related Data List and Active Test Items 
DTC No.
Data List Item
Active Test Item
B2285
Power Source Control
  1. Steering Unlock Switch
Entry & Start
  1. Power Supply Short
  2. Lock Bar Stuck Error
  3. Motor Driver Short
-

WIRING DIAGRAM


B271501E03


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
  2. The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (Click here).
  3. Before replacing the certification ECU (smart key ECU assembly) or steering lock actuator assembly (steering lock ECU), refer to the entry and start system (for Entry Function) (Click here).
  4. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
  5. Inspect the fuses of circuits related to this system before performing the following inspection procedure.

HINT:
If the entry key indicator in the combination meter assembly illuminates in green, the steering lock bar may be stuck.

1.CHECK FOR DTC (LIN COMMUNICATION SYSTEM)
  1. Clear the DTCs (Click here).

    OK:
    LIN communication system DTC B2785 is not output simultaneously.

    HINT:
    1. If the steering wheel cannot be locked or unlocked, the engine switch cannot be turned on (IG) and the engine cannot be started.
    2. If LIN communication is not available, the steering wheel cannot be locked or unlocked.



NG
GO TO LIN COMMUNICATION SYSTEM (Click here)
OK


2.READ VALUE USING GTS (STEERING UNLOCK SWITCH)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. According to the display on the GTS, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Steering Unlock Switch
    State of steering unlock sensor signal output from steering lock actuator assembly/OFF or ON
    OFF: Steering locked
    ON: Steering unlocked
    1. When the shift lever is in P* and the engine switch is off, if any door is opened or closed, the steering is locked.
    2. When the electrical key transmitter sub-assembly is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks.
    3. The engine cannot be started when the steering unlock signal is off.

    1. *: for Automatic Transmission
    Result 
    Result
    Proceed to
    Data List item does not change
    A
    Data List item changes (for LHD)
    B



B
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (Click here)
A


3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B268625E18
  1. Disconnect the D48 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D48-2 (+B) - Body ground
    Always
    9.5 to 16 V

    Text in Illustration 
    *a
    Rear view of harness connected
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


4.CHECK HARNESS AND CONNECTOR (GROUND)
B268625E19
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of harness connected
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)
  1. Reconnect the D59 steering lock actuator assembly (steering lock ECU) connector.



    C197722E73
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Positive (+) tester probe → D59-4 (SLP)
    Negative (-) tester probe → Body ground
    Steering locked*
    10 kΩ or higher
    Positive (+) tester probe → D59-4 (SLP)
    Negative (-) tester probe → Body ground
    Steering unlocked*
    Below 1 Ω

    HINT:
    1. *: If any of the doors are opened then closed with the shift lever in P* and the engine switch off, the steering wheel will be locked. If the engine switch is then turned on (ACC) or on (IG), the steering wheel will be unlocked.
    2. DTC B2285 may be stored due to a malfunction in the steering lock ECU (steering lock actuator assembly). The steering lock position signal and unlock position signal are sent from the steering lock ECU (steering lock actuator assembly) to the certification ECU (smart key ECU assembly) individually.

    1. *: for Automatic Transmission
    Text in Illustration 
    *a
    Component with harness connected
    (Steering Lock Actuator Assembly (Steering Lock ECU))



NG
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU))
  1. Disconnect the D41 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the D59 steering lock actuator assembly (steering lock ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D41-26 (SLP) - D59-4 (SLP1)
    Always
    Below 1 Ω
    D41-26 (SLP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)