Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1617    Front Airbag Sensor LH Lost Communication

DTC    B1618    Front Airbag Sensor LH Initialization

for Preparation Click here


DESCRIPTION

The front airbag sensor LH circuit consists of the airbag ECU assembly and front airbag sensor LH.
The front airbag sensor LH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbag should be deployed.
These DTCs are stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1617
B1618
  1. The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit.
  2. Front airbag sensor LH malfunction
  3. Airbag ECU assembly malfunction
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor LH
  4. Airbag ECU assembly

WIRING DIAGRAM


C244889E11


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor LH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag ECU assembly and front airbag sensor LH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)


    C238216E06
  1. Connect the connectors that link the engine room main wire and instrument panel wire.

  1. Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A58-2 (BUSIN) - A58-1 (RTNIN)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag ECU Assembly
    *3
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag ECU Assembly)
    *b
    Front view of wire harness connector
    (to Front Airbag Sensor LH)



NG
Go to step 7
OK


3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)


    C238212E12
  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A58-2 (BUSIN) - A58-1 (RTNIN)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag ECU Assembly
    *a
    Front view of wire harness connector
    (to Front Airbag Sensor LH)



NG
Go to step 8
OK


4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)


    C238212E12
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A58-2 (BUSIN) - Body ground
    Ignition switch ON
    Below 1 V
    A58-1 (RTNIN) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag ECU Assembly
    *a
    Front view of wire harness connector
    (to Front Airbag Sensor LH)



NG
Go to step 9
OK


5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)


    C238212E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A58-2 (BUSIN) - Body ground
    Always
    1 MΩ or higher
    A58-1 (RTNIN) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag ECU Assembly
    *a
    Front view of wire harness connector
    (to Front Airbag Sensor LH)



NG
Go to step 10
OK


6.CHECK FRONT AIRBAG SENSOR LH


    C238211E01
  1. Connect the connector to the airbag ECU assembly.

  1. Interchange the front airbag sensor LH with RH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1612, B1613, B1617 and B1618 are not output.
    A
    DTC B1617 or B1618 is output.
    B
    DTC B1612 or B1613 is output.
    C

    HINT:
    Codes other than DTCs B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the front airbag sensor LH and RH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Front Airbag Sensor RH
    *2
    Airbag ECU Assembly



B
REPLACE AIRBAG ECU ASSEMBLY (Click here)

C
REPLACE FRONT AIRBAG SENSOR LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

7.CHECK INSTRUMENT PANEL WIRE (OPEN)


    C247432E02
  1. Disconnect the instrument panel wire connector from the engine room main wire.

    HINT:
    The service wire has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DA3-4 - DA3-3
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.
    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag ECU Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *5
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag ECU Assembly)
    *b
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

8.CHECK INSTRUMENT PANEL WIRE (SHORT)


    C247431E04
  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DA3-4 - DA3-3
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag ECU Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)


    C247431E04
  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    DA3-4 - Body ground
    Ignition switch ON
    Below 1 V
    DA3-3 - Body ground
    Ignition switch ON
    Below 1 V

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag ECU Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)


    C247431E04
  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DA3-4 - Body ground
    Always
    1 MΩ or higher
    DA3-3 - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag ECU Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE