Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Low Beam Headlight Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (network gateway ECU) receives headlight dimmer switch assembly information signals, and illuminates the low beam headlight.

WIRING DIAGRAM


E252209E01


INSPECTION PROCEDURE

HINT:
Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING GTS (H-LP RELAY)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test

  1. Check that the relay operates.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Headlight Relay
    Low beam headlight relay
    ON/OFF
    -

    OK:
    Headlight relay operates (low beam headlights illuminate).

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)
A


2.INSPECT H-LP RELAY
  1. Remove the H-LP relay from the engine room relay block.

  1. Inspect the H-LP relay (Click here).



NG
REPLACE H-LP RELAY
OK


3.CHECK HARNESS AND CONNECTOR (H-LP RELAY - BATTERY)
E252212E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Engine Room Relay Block
    (H-LP Relay Terminal)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - MAIN BODY ECU (NETWORK GATEWAY ECU))
  1. Disconnect the A73 main body ECU (network gateway ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
Relay terminal 2 - A73-11 (DIM)
Always
Below 1 Ω

Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
A73-11 (DIM) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3C instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
Relay terminal 1 - 3C-17
Always
Below 1 Ω

Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
3C-17 - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))
  1. Disconnect the 3A and 3C instrument panel junction block assembly connector.

  1. Disconnect the D5 and A73 main body ECU (network gateway ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
3A-29 - D5-1
Always
Below 1 Ω
3C-30 - A73-2
Always
Below 1 Ω

Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
D5-1 - Body ground
Always
10 kΩ or higher
A73-2(HRLY) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.


E247166E01


Text in Illustration 
*a
Component without harness connected
(Instrument Panel Junction Block Assembly)
-
-

Standard Resistance:

Tester Connection
Condition
Specified Condition
3C-17 - 3A-29
Always
Below 1 Ω
3C-17 - 3C-30
Always
Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)