Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Remote Up / Down Function does not Operate

for Preparation Click here


DESCRIPTION

With the ignition switch ON, the power window regulator master switch assembly transmits remote operation signals to each power window regulator switch assembly. Then, the power window regulator switch assembly drives each power window regulator motor assembly.

WIRING DIAGRAM

Refer to DTCs B2312 and B2315 .

INSPECTION PROCEDURE

NOTICE:
  1. When the power window regulator master switch assembly, power window regulator switch assembly and power window regulator motor assembly is reinstalled or replaced, the power window control system must be initialized (Click here).
  2. When the jam protection function malfunctions and prevents the door glass from closing completely, the following procedure can be used to cancel the jam protection function and allow the door glass to be closed*1.
    1. Repeat the AUTO UP maintain → jam protection function operation twice in succession*2.
    2. The third repeat of the AUTO UP maintain operation will cause the position of the upper edge of the door glass to be relearned, allowing the door glass to be closed.
      1. *1: In some cases, the state of the door glass or regulator may prevent the glass from being closed, even in this mode.
      2. *2: If any action other that the AUTO UP operation (DOWN operation, IG OFF, timer-operated OFF, index operation, etc.) is performed between the operation of the jam protection function and the AUTO UP maintain, this count will be reset.

1.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (WINDOW LOCK SWITCH)
  1. Turn the window lock switch off and operate the switches on the power window regulator master switch assembly. Check that the remote UP/DOWN function operates normally.

    OK:
    Remote UP/DOWN function operates normally.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


2.READ VALUE USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the GTS.

    Master Switch 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    P Door P/W Remote Auto SW
    Front passenger side power window auto switch signal from driver side / ON or OFF
    ON: Front passenger side power window auto up/down switch from driver side operated
    OFF: Front passenger side power window switch from driver side not operated
    -
    P Door P/W Remote Up SW
    Front passenger side power window manual up signal from driver side / ON or OFF
    ON: Front passenger side power window manual up switch from driver side operated
    OFF: Front passenger side power window switch from driver side not operated
    -
    P Door P/W Remote Down SW
    Front passenger side power window manual down switch from driver side /OFF or ON
    ON: Front passenger side power window manual down switch from driver side operated
    OFF: Front passenger side power window switch from driver side not operated
    -

    OK:
    The GTS display changes normally when regulator switch is operated.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY)
  1. Disconnect the E8*1 or F6*2 power window regulator master switch assembly connector.

  1. Disconnect the F6*1 or E8*2 power window regulator switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    E8-2 (UART) - F6-2 (UART)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    E8-2 (UART)*1 - Body ground
    Always
    10 kΩ or higher
    F6-2 (UART)*2 - Body ground
    Always
    10 kΩ or higher

    1. *1: for LHD
    2. *2: for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)