Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

When the ignition switch is ON, the power window regulator motor assembly (for front passenger side) is operated by the power window regulator switch assembly. The power window regulator motor assembly (for front passenger side) has motor, regulator and ECU functions.

WIRING DIAGRAM


B315695E02


B315695E03


INSPECTION PROCEDURE

NOTICE:
  1. When the power window regulator master switch assembly, power window regulator switch assembly and power window regulator motor assembly is reinstalled or replaced, the power window control system must be initialized (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Master Switch / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Master Switch 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Front passenger side power window
    OFF / UP / DOWN
    -

    OK:
    Front passenger side door power window operates normally.

    CAUTION:
    Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.

Result 
Result
Proceed to
NG
A
OK
B


B
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
A


2.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - BATTERY)
  1. Disconnect the F6*1 or E8*2 power window regulator switch assembly connector.



    B322620E02
  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F6-12 (+B)*1 - Body ground
    Always
    11 to 14 V
    E8-12 (+B)*2 - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F6-5 (GND)*1 - Body ground
    Always
    Below 1 Ω
    E8-5 (GND)*2 - Body ground
    Always
    Below 1 Ω

    1. *1: for LHD
    2. *2: for RHD

Text in Illustration 
*A
for LHD
*B
for RHD
*a
Front view of wire harness connector
(to Front Power Window Regulator Switch Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - POWER WINDOW MOTOR)
  1. Disconnect the F6*1 or E8*2 power window regulator switch assembly connector.

  1. Disconnect the F1*1 or E5*2 power window regulator motor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    F6-6 (WU) - F1-1 (WU)*1
    Always
    Below 1 Ω
    F6-7 (WD) - F1-3 (WD)*1
    Always
    Below 1 Ω
    E8-6 (WU) - E5-1 (WU)*2
    Always
    Below 1 Ω
    E8-7 (WD) - E5-3 (WD)*2
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    F6-6 (WU)*1 - Body ground
    Always
    10 kΩ or higher
    F6-7 (WD)*1 - Body ground
    Always
    10 kΩ or higher
    E8-6 (WU)*2 - Body ground
    Always
    10 kΩ or higher
    E8-7 (WD)*2 - Body ground
    Always
    10 kΩ or higher

    1. *1: for LHD
    2. *2: for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY
  1. Temporarily replace the power window regulator switch assembly with a new or normally functioning one (Click here).

  1. Check the power window regulator switch assembly operates (Click here).

    OK:
    Front passenger side door power window operates normally.

Result 
Result
Proceed to
Operate
A
Does not operate
B


B
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (Click here)
A

END (POWER WINDOW REGULATOR SWITCH ASSEMBLY WAS DEFECTIVE)