Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Headlight Dimmer Switch Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (network gateway ECU) receives the following signals:
  1. Headlight dimmer switch tail, head, AUTO*1, high or high flash signal
  2. Front fog light switch signal*2
  3. Rear fog light switch signal*3
    1. *1: w/ Automatic Light Control System
    2. *2: w/ Front Fog Light
    3. *3: w/ Rear Fog Light

WIRING DIAGRAM


E252210E01


INSPECTION PROCEDURE

1.READ VALUE USING GTS (HEADLIGHT DIMMER SWITCH ASSEMBLY)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the display on the GTS.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Dimmer SW
    Dimmer switch high position signal / ON or OFF
    ON: Dimmer switch in high or high flash position
    OFF: Dimmer switch in low position
    -
    Passing Light SW
    Dimmer switch high flash position (pass) signal / ON or OFF
    ON: Dimmer switch in high flash position
    OFF: Dimmer switch not in high flash position
    -
    Rear Fog Light SW*3
    Rear fog light switch signal / ON or OFF
    ON: Rear fog light switch on
    OFF: Rear fog light switch off
    -
    Front Fog Light SW*2
    Front fog light switch signal / ON or OFF
    ON: Front fog light switch on
    OFF: Front fog light switch off
    -
    Auto Light SW*1
    Light control switch AUTO position signal / ON or OFF
    ON: Light control switch in AUTO position
    OFF: Light control switch not in AUTO position
    -
    Head Light SW (Head)
    Light control switch head position signal / ON or OFF
    ON: Light control switch in head position
    OFF: Light control switch not in head position
    -
    Head Light SW (Tail)
    Light control switch tail position signal / ON or OFF
    ON: Light control switch in tail or head position
    OFF: Light control switch in neither tail nor head position
    -
    Lighting Hi
    Light control switch head (Hi) position signal / ON or OFF
    ON: Headlight high beam on
    OFF: Headlight high beam off
    -

    1. *1: w/ Automatic Light Control System
    2. *2: w/ Front Fog Light
    3. *3: w/ Rear Fog Light

    OK:
    The display is as specified in the normal condition column.

    Result :
    Result
    Proceed to
    OK
    A
    NG (Dimmer switch)
    B
    NG (Fog switch and light control switch)
    C



B
Go to step 2

C
Go to step 4
A

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)  

2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
  1. Remove the headlight dimmer switch assembly (Click here).

  1. Inspect the headlight dimmer switch assembly (Click here).



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - JUNCTION BLOCK ASSEMBLY, BODY GROUND)
  1. Disconnect the 3B junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    D50-17 (HF) - 3B-15
    Always
    Below 1 Ω
    D50-11 (HU) - 3B-30
    Always
    Below 1 Ω
    D50-12 (EL) - Body ground
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    D50-14 (HF) - 3B-15
    Always
    Below 1 Ω
    D50-20 (HU) - 3B-30
    Always
    Below 1 Ω
    D50-19 (EL) - Body ground
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    D50-17 (HF) - Body ground
    Always
    10 kΩ or higher
    D50-11 (HU) - Body ground*1
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    D50-14 (HF) - Body ground
    Always
    10 kΩ or higher
    D50-20 (HU) - Body ground*1
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
  1. Remove the headlight dimmer switch assembly (Click here).

  1. Inspect the headlight dimmer switch assembly (Click here).



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))
  1. Disconnect the D5 main body ECU (network gateway ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    D50-2 (B) - D5-26 (RFOG)*3
    Always
    Below 1 Ω
    D50-4 (BFG) - D5-24 (FFOG)*2
    Always
    Below 1 Ω
    D50-20 (H) - D5-2 (HEAD)
    Always
    Below 1 Ω
    D50-19 (A) - D5-23 (A)*1
    Always
    Below 1 Ω
    D50-18 (T) - D5-25 (TAIL)
    Always
    Below 1 Ω
    D50-12 (EL) - Body ground
    Always
    Below 1 Ω
    D50-3 (LFG) - Body ground
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    D50-7 (B) - D5-26 (RFOG)*3
    Always
    Below 1 Ω
    D50-9 (BFG) - D5-24 (FFOG)*2
    Always
    Below 1 Ω
    D50-11 (H) - D5-2 (HEAD)
    Always
    Below 1 Ω
    D50-12 (A) - D5-23 (A)*1
    Always
    Below 1 Ω
    D50-13 (T) - D5-25 (TAIL)
    Always
    Below 1 Ω
    D50-19 (EL) - Body ground
    Always
    Below 1 Ω
    D50-8 (LFG) - Body ground
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    D50-2 (B)*3 - Body ground
    Always
    10 kΩ or higher
    D50-4 (BFG)*2 - Body ground
    Always
    10 kΩ or higher
    D50-20 (H) - Body ground
    Always
    10 kΩ or higher
    D50-19 (A)*1 - Body ground
    Always
    10 kΩ or higher
    D50-18 (T) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    D50-7 (B)*3 - Body ground
    Always
    10 kΩ or higher
    D50-9 (BFG)*2 - Body ground
    Always
    10 kΩ or higher
    D50-11 (H) - Body ground
    Always
    10 kΩ or higher
    D50-12 (A)*1 - Body ground
    Always
    10 kΩ or higher
    D50-13 (T) - Body ground
    Always
    10 kΩ or higher

  1. *1: w/ Automatic Light Control System
  2. *2: w/ Front Fog Light
  3. *3: w/ Rear Fog Light


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)