Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR

FRONT DOOR > REASSEMBLY

for Preparation Click here


HINT:
Use the same procedure for both the RH and LH sides.



1. INSTALL FRONT DOOR HOLE COVER


    B314813
  1. Insert the front door hole cover with the 4 claws.



2. INSTALL DOOR SIDE AIR BAG SENSOR
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    The power window system utilizes a mechanism that the door glass moves down slightly when the door is opened, and that the glass moves up when closing the door in order to prevent the door molding from being damaged. When the battery negative (-) terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



    B311396
  1. Connect the connector to the door side airbag sensor.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.


    1. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

  1. Insert the pin (stopper) into the door hole and install the door side airbag sensor to the front door panel with the nut.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    NOTICE:
    1. If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
    3. Make sure that the pin (stopper) is securely inserted into the body hole.
    4. Tighten the nut while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

  1. Check that there is no looseness in the installation parts of the door side airbag sensor.



3. INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B314915
  1. Engage the claws to install the screw and new front door glass outer weatherstrip assembly as shown in the illustration.



4. INSTALL FRONT DOOR PANEL CUSHION


    B314812
  1. Engage the 2 claws and install 2 new front door panel cushions.



5. INSTALL FRONT DOOR CHECK ASSEMBLY
  1. Apply MP grease to the sliding areas of the front door check assembly.



    B314811
  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the bolt.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

  1. Install the front door check assembly with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



6. INSTALL FRONT DOOR LOCK OPEN ROD


    B314814E01
  1. Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.



7. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
  1. Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.



    B314815E01
  1. Engage the claw.

  1. Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    Text in Illustration 
    *a
    Outside Vehicle
    *b
    Inside Vehicle



8. INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD


    B314807
  1. Engage the 3 claws and install the front door front outside handle pad.



9. INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD


    B314808
  1. Engage the 2 claws and install the front door rear outside handle pad.



10. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/ Entry and Start System)


    B314816
  1. Insert the front end of the front door outside handle assembly into the front door outside handle frame sub-assembly.

  1. Insert the rear end of the front door outside handle assembly into the front door outside handle frame sub-assembly, and then slide the front door outside handle assembly toward the front of the vehicle to install it.



    B314817
  1. Connect the connector.

  1. Engage the 3 claws.



    B314805
  1. Engage the clamp.



11. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/o Entry and Start System)


    B314816
  1. Insert the front end of the front door outside handle assembly into the front door outside handle frame sub-assembly.

  1. Insert the rear end of the front door outside handle assembly into the front door outside handle frame sub-assembly, and then slide the front door outside handle assembly toward the front of the vehicle to install it.



12. INSTALL FRONT DOOR LOCK ASSEMBLY

NOTICE:
Do not allow grease or dust to adhere to the surface of the connector which contacts the door lock wire harness seal.

  1. Apply MP grease to the sliding parts of the front door lock assembly.

  1. Insert the front door lock open rod into the front door lock assembly.

  1. Check that the front door lock open rod is securely connected to the front door lock assembly.

  1. Install the front door lock assembly with the 3 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



13. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)


    B228719
  1. Engage the claw and 2 guides, and install the front door outside handle cover to the front door lock cylinder assembly.



14. INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)


    B314818
  1. Install the front door outside handle cover with front door lock cylinder assembly.

    HINT:
    Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.



    B314802
  1. Using a T30 "TORX" socket wrench, install the front door lock cylinder assembly with the screw.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



15. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    B314803
  1. Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



16. INSTALL FRONT DOOR WEATHERSTRIP
  1. Engage the 16 clips.

  1. Engage the claw.



  1. Install the front door weatherstrip with the screw.


    B314801



17. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY
  1. Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



18. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding parts of the front door window regulator sub-assembly.

  1. Install the temporary bolt to the front door window regulator sub-assembly.



    B314800E01
  1. Temporarily install the front door window regulator sub-assembly.

  1. Tighten the 3 bolts and 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Tighten the temporary bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.
    Text in Illustration 
    *1
    Temporary Bolt



19. INSTALL FRONT DOOR SASH STOPPER
  1. Install the front door sush stopper with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



20. INSTALL FRONT DOOR SUSH


    B314820E01
  1. Insert the front door sush so that it is perpendicular to the front door frame, in the order shown in the illustration.

  1. Rotate the front door sush 90°.

    NOTICE:
    Do not damage the front door sush.



    B314797E01
  1. Install the front door sush with the 3 nuts.

    Torque:
    Nut(A):
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    Torque:
    Nut(B):
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



21. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the power window regulator master switch assembly connector (for driver side).

  1. Connect the power window regulator switch assembly connector (for front passenger side).

  1. Move the front door glass sub-assembly until the 2 nuts can be seen through the service holes.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the power window regulator master switch assembly connector (for driver side).

  1. Disconnect the power window regulator switch assembly connector (for front passenger side).



    B314796
  1. Insert the front door glass sub-assembly into the front door frame from the position indicated in the illustration.

    NOTICE:
    Do not damage the front door weatherstrip.

    HINT:
    The front door glass sub-assembly can only be installed from the position indicated in the illustration, so install it while sliding the front door rear lower frame sub-assembly.

  1. Insert the grommet of front door glass assembly into the rail of the front door rear lower frame sub-assembly.



    B386126E01
  1. Install a new nut B temporarily to the front door glass sub-assembly.
    Text in Illustration  
    *1
    Nut A
    *2
    Nut B
    *3
    Front Door Glass Sub-assembly
    *4
    Front Door Window Regulator Sub-assembly
    *5
    Bolt
    *a
    SST Number

  1. Install SST as shown in the illustration.

    SST
    09801-18010  

    HINT:
    The SST number on SST must be visible.

  1. Secure the bolt using SST, and then tighten a new nut A to the specified torque.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Tighten nut B to the specified torque.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



22. INSTALL DOOR GLASS INNER STABILIZER
  1. Install the door glass inner stabilizer with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



23. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
  1. Install the front door rear lower frame sub-assembly with the 3 nuts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



24. INSTALL OUTER REAR VIEW MIRROR SUB-ASSEMBLY



25. ADJUST FRONT DOOR GLASS SUB-ASSEMBLY
  1. Check the front door glass sub-assembly .

  1. Adjust the front door glass sub-assembly .



26. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the front door panel.



  1. Pass the front door lock remote control cable assembly and the front door inside locking cable assembly through a new front door service hole cover.


    B314821E01


    Text in Illustration 
    *1
    Reference Point
    -
    -

  1. Attach the front door service hole cover according to the reference points on the front door panel.

    NOTICE:
    1. Overlay the butyl tape in lengths of 20 cm (7.874 in.) or more.
    2. Do not block the drip holes in the front door panel with butyl tape.
    3. Securely install the front door service hole cover preventing wrinkles and air bubbles.

  1. Connect each connector.



27. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY (w/ Front Speaker)
  1. Install the front No. 1 speaker assembly with the 3 screws.

    NOTICE:
    Do not touch the speaker cone.

  1. Connect the connector.



28. INSTALL FRONT DOOR SPEAKER HOLE COVER (w/o Front Speaker)


    B309247
  1. Install the front door speaker hole cover with the 3 screws.



29. INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP


    B373753
  1. Engage the 9 claws to install a new front door glass inner weatherstrip to the front door trim board sub-assembly as shown in the illustration.



    B314823
  1. Install a nose piece to an air riveter, and then insert the mandrel part of a new rivet into the nose piece.

  1. Hold the riveter perpendicular against the moulding and install the 6 rivets.

    HINT:
    If the rivet cannot be cut, pull it once again to cut it. Also, be sure to cut off the head.

    NOTICE:

    1. B171664E17
      Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.
      Text in Illustration  
      *1
      Riveter
      *2
      Mandrel
      *a
      Incorrect
      *b
      Correct

    2. B172390E17
      Confirm that the rivets are seated properly against the front door glass inner weatherstrip.
      Text in Illustration  
      *1
      Riveter
      *a
      Incorrect
      *b
      Correct
    3. Do not tilt the riveter when installing the rivet to the front door glass inner weatherstrip
    4. Do not leave any space between the rivet head and front door glass inner weatherstrip.



    B373209E01
  1. After installing the rivet, cut nonwoven tape into a 15 mm (0.591 in.) x 15 mm (0.591 in.) square and attach it to the crimped section of the rivet.
    Text in Illustration  
    *1
    Front Door Glass Sub-assembly
    *2
    Front Door Trim Board Sub-assembly
    *3
    Nonwoven Tape
    *4
    Rivet
    *5
    Front Door Glass Inner Weatherstrip

    NOTICE:
    1. The crimp height of the rivet must be 3 mm (0.118 in.).
    2. If the crimp is not firm enough, flatten it using pliers or the like to avoid interference with the door panel.

  1. After installing the front door glass inner weatherstrip, check the following items:

    1. Check that there is no gap between the front door glass inner weatherstrip and the front door trim board sub-assembly.
    2. Pull the front door glass inner weatherstrip lightly and check that there is no play.



30. INSTALL FRONT LOWER DOOR TRIM PAD


    B314157
  1. Install the front lower door trim pad with the 5 screws.



31. INSTALL DOOR ASSIST GRIP ASSEMBLY


    B314156
  1. Engage the guide and install the door assist grip assembly with the 2 screws.



32. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B314154
  1. Install the power window regulator master switch assembly with front door armrest base panel with the 4 screws.



33. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    B314155
  1. Install the power window regulator switch assembly with front door armrest base panel with the 4 screws.



34. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B314153
  1. Engage the 2 guides.

  1. Install the front door inside handle sub-assembly to the front door trim board sub-assembly with the 2 screws.



35. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B313122E01
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable Assembly
    *2
    Front Door Lock Remote Control Cable Assembly

  1. Connect each connector.



    B314824
  1. Engage the 10 clips and install the front door trim board sub-assembly.



    B313120
  1. Engage the clip and install the 3 screws.



    B314825
  1. Engage the claw and install the cap.



36. INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
  1. Connect the connector.



    E255534E01
  1. Engage the claw to install the courtesy light assembly.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



37. INSTALL DOOR ARMREST COVER


    B314960
  1. Engage the guide and 7 claws, and install the door armrest cover.



38. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



39. INITIALIZE POWER WINDOW CONTROL SYSTEM
(Click here)


40. INSPECT POWER WINDOW
(Click here)