Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > REMOVAL

for Preparation Click here



1. PRECAUTION

CAUTION:
Be sure to read Precaution thoroughly before servicing (Click here).

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. for HFC-134a (R134a):

  1. for HFO-1234yf (R1234yf):



3. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator cap, cylinder block drain cock plugs and radiator drain cock plug while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the local regulations.



    A277916
  1. Remove the service hole cover from the front bumper under cover.

  1. Connect a hose with an inside diameter of 8 mm (0.315 in.) to the drain plug.



    A277917
  1. Loosen the radiator drain cock plug.



    A279728
  1. Open the air bleed plug on the heater hose side. (for LHD)



    A279727
  1. Open the air bleed plug on the heater hose side. (for RHD)

  1. Remove the radiator cap and drain the coolant.



4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. The power window system utilizes a mechanism that the door glass moves down slightly when the door is opened, and that the glass moves up when closing the door in order to prevent the door molding from being damaged. When the battery negative (-) terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



5. DISCONNECT INLET HEATER WATER HOSE A


    E250341
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose A.

    NOTICE:
    1. Do not apply excessive force to the inlet heater water hose A.
    2. Prepare a drain pan or cloth in case the coolant leaks.
    3. Since the inlet heater water hose A must be installed in a predefined position, apply matching marks before removing it.



6. DISCONNECT OUTLET HEATER WATER HOSE A


    E250342
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose A.

    NOTICE:
    1. Do not apply excessive force to the outlet heater water hose A.
    2. Prepare a drain pan or cloth in case the coolant leaks.
    3. Since the outlet heater water hose A must be installed in a predefined position, apply matching marks before removing it.



7. DISCONNECT SUCTION HOSE SUB-ASSEMBLY


    E246449
  1. Remove the bolt and slide the hook connector.

  1. Disconnect the suction hose sub-assembly.

  1. Remove the O-ring from the suction hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



8. DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
  1. Disconnect the air conditioner tube and accessory assembly.

  1. Remove the O-ring from the air conditioner tube and accessory assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



9. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


10. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY (w/ Knee Airbag)

CAUTION:
When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.

  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    The power window system utilizes a mechanism that the door glass moves down slightly when the door is opened, and that the glass moves up when closing the door in order to prevent the door molding from being damaged. When the battery negative (-) terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



    B311366
  1. Remove the 2 nuts and remove the lower No. 1 instrument panel airbag assembly.

    NOTICE:
    When removing the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.



    B311367E01
  1. Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Airbag Connector
    *3
    Airbag Connector Lock

  1. Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.



11. REMOVE STEERING COLUMN ASSEMBLY
(Click here)


12. REMOVE FRONT DOOR SCUFF PLATE LH


    B315201
  1. Disengage the 6 claws and remove the front door scuff plate LH.



13. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



14. REMOVE COWL SIDE TRIM BOARD LH


    B315202
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board LH.



15. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure described for the LH side.



16. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY


  1. for Driver Side



    1. Using a T20 "TORX" socket wrench, remove the 2 bolts.


      E255871E01


      Text in Illustration 
      *1
      "TORX" Bolt
      -
      -

    2. Remove the bolt.

    3. Disconnect each connector and disengage the clamp and 2 claws.



  1. for Center Side



    1. Remove the each bolts and disengage the clip.


      E255872E01


      Text in Illustration 
      *A
      for Automatic Air Conditioning System
      -
      -
      *a
      Disengage the lock plate and disconnect connector.
      -
      -

    2. Disconnect each connector and disengage the each clamp.



  1. for Front Passenger Side



    1. Using a T20 "TORX" socket wrench, remove the 2 bolts.


      E256300E01


      Text in Illustration 
      *A
      for RHD
      -
      -
      *1
      "TORX" Bolt
      -
      -

    2. Remove the each bolts.

    3. Disconnect each connector and disengage the 2 clamps and 2 claws.

  1. Remove the instrument panel reinforcement assembly.



17. REMOVE AIR CONDITIONING UNIT ASSEMBLY (for Automatic Air Conditioning System)


  1. Disconnect each connector and disengage each clamp.


    E246437



    E246443
  1. Disengage the drain cooler hose.



  1. Remove the 3 bolts, 3 nuts and air conditioning unit assembly.


    E252236E01


    Text in Illustration 
    *1
    Bolt
    *2
    Nut



18. REMOVE AIR CONDITIONING UNIT ASSEMBLY (for Manual Air Conditioning System)


  1. Disconnect each connector and disengage each clamp.


    E246438



    E246443
  1. Disengage the drain cooler hose.



  1. Remove the 3 bolts, 3 nuts and air conditioning unit assembly.


    E252237E01


    Text in Illustration 
    *1
    Bolt
    *2
    Nut



19. REMOVE AIR CONDITIONING UNIT ASSEMBLY (w/o Air Conditioning System)


  1. Disconnect each connector and disengage each clamp.


    E246439



    E246443
  1. Disengage the drain cooler hose.



  1. Remove the 3 bolts, 3 nuts and air conditioning unit assembly.


    E252237E01


    Text in Illustration 
    *1
    Bolt
    *2
    Nut