Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR BELT MOULDING

FRONT DOOR BELT MOULDING > INSTALLATION

for Preparation Click here


HINT:
Use the same procedure for both the RH and LH sides.



1. INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B314915
  1. Engage the claws to install the screw and new front door glass outer weatherstrip assembly as shown in the illustration.



2. INSTALL FRONT DOOR SUSH


    B314820E01
  1. Insert the front door sush so that it is perpendicular to the front door frame, in the order shown in the illustration.

  1. Rotate the front door sush 90°.

    NOTICE:
    Do not damage the front door sush.



    B314797E01
  1. Install the front door sush with the 3 nuts.

    Torque:
    Nut(A):
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    Torque:
    Nut(B):
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the power window regulator master switch assembly connector (for driver side).

  1. Connect the power window regulator switch assembly connector (for front passenger side).

  1. Move the front door glass sub-assembly until the 2 nuts can be seen through the service holes.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the power window regulator master switch assembly connector (for driver side).

  1. Disconnect the power window regulator switch assembly connector (for front passenger side).



    B314796
  1. Insert the front door glass sub-assembly into the front door frame from the position indicated in the illustration.

    NOTICE:
    Do not damage the front door weatherstrip.

    HINT:
    The front door glass sub-assembly can only be installed from the position indicated in the illustration, so install it while sliding the front door rear lower frame sub-assembly.

  1. Insert the grommet of front door glass assembly into the rail of the front door rear lower frame sub-assembly.



    B386126E01
  1. Install a new nut B temporarily to the front door glass sub-assembly.
    Text in Illustration  
    *1
    Nut A
    *2
    Nut B
    *3
    Front Door Glass Sub-assembly
    *4
    Front Door Window Regulator Sub-assembly
    *5
    Bolt
    *a
    SST Number

  1. Install SST as shown in the illustration.

    SST
    09801-18010  

    HINT:
    The SST number on SST must be visible.

  1. Secure the bolt using SST, and then tighten a new nut A to the specified torque.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Tighten nut B to the specified torque.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



4. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
  1. Install the front door rear lower frame sub-assembly with the 3 nuts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



5. ADJUST FRONT DOOR GLASS SUB-ASSEMBLY
  1. Check the front door glass sub-assembly .

  1. Adjust the front door glass sub-assembly .



6. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the front door panel.



  1. Pass the front door lock remote control cable assembly and the front door inside locking cable assembly through a new front door service hole cover.


    B314821E01


    Text in Illustration 
    *1
    Reference Point
    -
    -

  1. Attach the front door service hole cover according to the reference points on the front door panel.

    NOTICE:
    1. Overlay the butyl tape in lengths of 20 cm (7.874 in.) or more.
    2. Do not block the drip holes in the front door panel with butyl tape.
    3. Securely install the front door service hole cover preventing wrinkles and air bubbles.

  1. Connect each connector.



7. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B314154
  1. Install the power window regulator master switch assembly with front door armrest base panel with the 4 screws.



8. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    B314155
  1. Install the power window regulator switch assembly with front door armrest base panel with the 4 screws.



9. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B313122E01
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable Assembly
    *2
    Front Door Lock Remote Control Cable Assembly

  1. Connect each connector.



    B314824
  1. Engage the 10 clips and install the front door trim board sub-assembly.



    B313120
  1. Engage the clip and install the 3 screws.



    B314825
  1. Engage the claw and install the cap.



10. INSTALL DOOR ARMREST COVER


    B314960
  1. Engage the guide and 7 claws, and install the door armrest cover.



11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



12. INITIALIZE POWER WINDOW CONTROL SYSTEM
(Click here)


13. INSPECT POWER WINDOW OPERATION
(Click here)