STEERING LOCK SYSTEM > Unable to Lock Steering Wheel |
| Problem Symptom | Data List Item | Active Test Item |
| Unable to lock steering wheel | Entry&Start
Main Body
| - |

| 1.CHECK DTC (ALL) |
Using the GTS, confirm the output of DTCs for all systems.
|
| ||||
| OK | |
| 2.READ VALUE USING GTS (LOCK REQUEST RECEIVE) |
Use the Data List to check if the steering lock command is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Lock Request Receive*1 | Reception state of steering lock command signal determined by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG
| OK: Within 10 seconds of opening any door with engine switch off and shift lever in P*3 NG: Except above | If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Lock Request Receive*2 | Reception state of steering lock command signal determined by certification ECU (smart key ECU assembly) / OK or NG
| OK: Within 10 seconds of opening any door with engine switch off and shift lever in P*3 NG: Except above | If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
|
| ||||
| OK | |
| 3.CHECK STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (MOTOR ACTIVATION COMMAND SIGNAL) |
Disconnect the D59 steering lock actuator assembly (steering lock ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D59-1 (SLR+) - Body ground | Always | Below 1 Ω |
Reconnect the D59 steering lock actuator assembly (steering lock ECU) connector.
Turn the engine switch off, make sure that the steering is unlocked and move the shift lever to P*.
![]() |
Check the signal waveform according to the condition(s) in the table below.
| Item | Content |
| Tester Connection | D59-3 (SLR+) - D59-1 (GND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating |
| *a | Component with harness connected (Steering Lock Actuator Assembly (Steering Lock ECU)) |
| *b | Steering lock motor not operating |
| *c | Steering lock motor operating |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)) |
Disconnect the D41 certification ECU (smart key ECU assembly) connector.
Disconnect the D59 steering lock actuator assembly (steering lock ECU) connector.
Check for deformation and corrosion of the connector case and terminals.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D41-29 (SLR+) - D59-3 (SLR+) | Always | Below 1 Ω |
| D59-3 (SLR+) - Body ground | Always | 10 kΩ or higher |
| D41-29 (SLR+) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.READ VALUE USING GTS (D DOOR COURTESY SW) |
Using the GTS, check the following main body ECU (network gateway ECU) Data List item by opening and closing the driver door to confirm the state of the driver side door courtesy light switch.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D Door Courtesy SW | Driver side door courtesy switch / ON or OFF | ON: Driver side door open OFF: Driver side door closed | If this item does not change according to the actual state of the driver side door, there is a malfunction in the door courtesy light switch or related part. |
| Result | Proceed to |
| OK (w/o ID Code Box) | A |
| OK (w/ ID Code Box) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 6.READ VALUE USING GTS (L CODE CHECK) |
Use the Data List to check if L code certification is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| L Code Check | Verification result between certification ECU (smart key ECU assembly) and steering lock actuator assembly / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
|
| ||||
| OK | |
| 7.REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) |
Replace the steering lock actuator assembly (steering lock ECU) with a new one (Click here).
Perform registration (refer to Service Bulletin).
Turn the engine switch on (IG).
Turn the steering wheel and check the steering condition.
|
| ||||
| OK | ||
| ||
| 8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Replace the certification ECU (smart key ECU assembly) with a new one.
Perform registration (refer to Service Bulletin).
Use the Data List to check if L code certification is functioning properly again.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| L Code Check | Verification result between certification ECU (smart key ECU assembly) and steering lock actuator assembly / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
|
| ||||
| OK | ||
| ||
| 9.READ VALUE USING GTS (S CODE CHECK) |
Use the Data List to check if S code certification is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
|
| ||||
| OK | |
| 10.READ VALUE USING GTS (L CODE CHECK) |
Use the Data List to check if L code certification is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| L Code Check | Verification result between ID code box (immobiliser code ECU) and steering lock actuator assembly / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
|
| ||||
| OK | |
| 11.REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) |
Replace the steering lock actuator assembly (steering lock ECU) with a new one (Click here).
Perform registration (refer to Service Bulletin).
Turn the engine switch on (IG).
Turn the steering wheel and check the steering condition.
|
| ||||
| OK | ||
| ||
| 12.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Replace the certification ECU (smart key ECU assembly) with a new one.
Perform registration (refer to Service Bulletin).
Use the Data List to check if S code certification is functioning properly again.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
|
| ||||
| OK | ||
| ||
| 13.REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) |
Replace the steering lock actuator assembly (steering lock ECU) with a new one (Click here).
Perform registration (refer to Service Bulletin).
Use the Data List to check if L code certification is functioning properly again.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| L Code Check | Verification result between ID code box (immobiliser code ECU) and steering lock actuator assembly / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
|
| ||||
| OK | ||
| ||