Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

AIRBAG SYSTEM > Trouble in Passenger Airbag ON/OFF Indicator

for Preparation Click here


DESCRIPTION

This circuit detects the airbag cut off switch status.
The passenger airbag ON/OFF indicator comes on to inform the front passenger airbag status (activated or deactivated).

HINT:
Approximately 6 seconds after the ignition switch is turned ON, the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the conditions listed below.

Airbag Cut Off Switch
Passenger Airbag ON/OFF Indicator
SRS Warning Light
ON Indicator
OFF Indicator
ON position
ON
OFF
OFF
OFF position
OFF
ON
OFF
Switch failure
OFF
ON
ON


WIRING DIAGRAM


C263719E01


INSPECTION PROCEDURE

HINT:
Terminals D27-14 (MSW+) and D27-12 (MSW-) of the airbag ECU assembly in this circuit have an activation prevention mechanism.
This mechanism can be used to check for an open circuit in the wire harness. In case of other checks (check for short, short to ground or short to B+), this mechanism should be released.

1.CHECK SRS WARNING LIGHT
  1. Turn the ignition switch ON, and check the SRS warning light condition.

    HINT:
    If this trouble occurs, the SRS warning light is off. If it is on, a DTC is stored. Troubleshoot for the stored DTC.

    OK:
    After the primary check period, the SRS warning light goes off.

    HINT:
    The primary check period is approximately 6 seconds after the ignition switch is turned ON.



NG
GO TO DTC CHART (Click here)
OK


2.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag ECU assembly and airbag cut off switch.

    OK:
    The connectors are properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connectors from the airbag ECU assembly and airbag cut off switch.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the short spring for the instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.



NG
REPLACE INSTRUMENT PANEL WIRE
OK


3.CHECK INSTRUMENT PANEL WIRE (OPEN)
  1. Using a service wire, connect terminals 12 (MSW-) and 14 (MSW+) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



    C263720E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D37-2 (MSW+) - D37-1 (MSW-)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Airbag Cut Off Switch
    *2
    Airbag ECU Assembly
    *3
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Airbag ECU Assembly)
    *b
    Front view of wire harness connector
    (to Airbag Cut Off Switch)



NG
REPLACE INSTRUMENT PANEL WIRE
OK


4.CHECK INSTRUMENT PANEL WIRE (SHORT)


    C263721E01
  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D37-2 (MSW+) - D37-1 (MSW-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Airbag Cut Off Switch
    *2
    Airbag ECU Assembly
    *3
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Airbag Cut Off Switch)



NG
REPLACE INSTRUMENT PANEL WIRE
OK


5.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)


    C263721E01
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D37-1 (MSW-) - Body ground
    Ignition switch ON
    Below 1 V
    D37-2 (MSW+) - Body ground
    Ignition switch ON
    Below 1 V

Text in Illustration 
*1
Airbag Cut Off Switch
*2
Airbag ECU Assembly
*3
Instrument Panel Wire
*a
Front view of wire harness connector
(to Airbag Cut Off Switch)


NG
REPLACE INSTRUMENT PANEL WIRE
OK


6.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)


    C263721E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D37-1 (MSW-) - Body ground
    Always
    1 MΩ or higher
    D37-2 (MSW+) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Airbag Cut Off Switch
    *2
    Airbag ECU Assembly
    *3
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Airbag Cut Off Switch)



NG
REPLACE INSTRUMENT PANEL WIRE
OK


7.CHECK AIRBAG CUT OFF SWITCH


    B311951E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (MSW+) - 1 (MSW-)
    Cut off switch in ON
    100 Ω
    Cut off switch in OFF
    400 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Airbag Cut Off Switch)



NG
REPLACE AIRBAG CUT OFF SWITCH (Click here)
OK

REPLACE AIRBAG ECU ASSEMBLY (Click here)