WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System) > No Answer-Back |

| 1.READ VALUE USING GTS (ANSWER-BACK OPERATION) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Utility / Customize / Wireless Door Lock.
Select the setting by referring to the table below.
| Display | Default | Content | Setting | Relevant ECU |
| Hazard Answer Back | ON | When the doors are locked by wireless operation, the hazard warning lights flash once. When the doors are unlocked by wireless operation, the hazard warning lights flash twice. | OFF or ON | Main body ECU (network gateway ECU) |
| Wireless Buzzer Resp* | ON | Wireless door lock buzzer response | OFF or ON | Main body ECU (network gateway ECU) |
| Wireless Buzzer Vol* | Level 5 | Wireless door lock buzzer volume | Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level 0 | Main body ECU (network gateway ECU) |
| Result | Proceed to |
| Both items are ON and except Level 0 | A |
| Either item is OFF or Level 0 | B |
|
| ||||
| A | |
| 2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS |
Check the wireless door lock control function using the door control transmitter module set sub-assembly.
| Result | Proceed to |
| Wireless door lock/unlock operates normally (w/ Wireless Door Lock Buzzer Answer-back Function). | A |
| Wireless door lock/unlock operates normally (w/o Wireless Door Lock Buzzer Answer-back Function). | B |
| Wireless door lock/unlock does not operate normally. | C |
|
| ||||
|
| ||||
| A | |
| 3.CHECK WIRELESS ANSWER-BACK OPERATION |
Check the wireless answer-back operation using the door control transmitter module set sub-assembly.
| Result | Proceed to |
| Only wireless door lock buzzer answer-back does not occur. | A |
| Only hazard warning light answer-back does not occur. | B |
|
| ||||
| A | |
| 4.PERFORM ACTIVE TEST USING GTS (WIRELESS DOOR LOCK BUZZER) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Wireless Buzzer | Turns the wireless door lock buzzer | ON/OFF | - |
| Result | Proceed to |
| Wireless door lock buzzer does not turn on/off. | A |
| Wireless door lock buzzer turns on/off. | B |
|
| ||||
| A | |
| 5.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU) |
Disconnect the A63 wireless door lock buzzer connector.
Disconnect the A73 main body ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A63-1 (+) - A73-1 (BZR) | Always | Below 1 Ω |
| A63-2 (-) - Body ground | Always | Below 1 Ω |
| A63-1 (+) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.REPLACE WIRELESS DOOR LOCK BUZZER |
Temporarily replace the wireless door lock buzzer with a new one (Click here).
| NEXT | |
| 7.CHECK WIRELESS DOOR LOCK BUZZER OPERATION |
Check the operation of the wireless answer-back function.
|
| ||||
| OK | ||
| ||
| 8.HAZARD WARNING LIGHTS OPERATION |
Check that the hazard warning light blinks when the hazard warning signal switch is pressed.
|
| ||||
| OK | |
| 9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
Remove the instrument panel junction block assembly (Click here).
Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.

| *a | Component without harness connected (Instrument Panel Junction Block Assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
| 3B-14 - MB-3 (HZR) | Always | Below 1 Ω |
| 3B-16 - MB-3 (HZR) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||