Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Air Conditioning Amplifier Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Air Conditioning Amplifier Communication Stop Mode
Either condition is met:
  1. "Air Conditioning Amplifier" is not displayed on the "CAN Bus Check" screen of the GTS (Click here)
  2. Communication system DTCs (DTCs that start with U) that are output correspond to "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" (Click here)
  1. Air conditioning control assembly branch line or connector
  2. Power source circuit of air conditioning control assembly
  3. Air conditioning control assembly ground circuit
  4. Air conditioning control assembly

WIRING DIAGRAM


C261294E01


C261294E02


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON, wait at least 10 seconds,
  6. After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING CONTROL ASSEMBLY BRANCH LINE)
  1. Disconnect the cable from the negative (-) battery terminal.



    C261283E02
  1. Disconnect the D19 air conditioning control assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Value
    D19-13 (CANH) - D19-12 (CANL)
    Cable disconnected from negative (-) battery terminal
    57 to 63 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Air Conditioning Control Assembly)



NG
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY)
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    C261283E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Value
    D19-16 (GND) - Body ground
    Cable disconnected from negative (-) battery terminal
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (to Air Conditioning Control Assembly)

  1. Connect the cable to the negative (-) battery terminal.



    C261283E04
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Value
    D19-9 (+B) - Body ground
    Ignition switch off
    11 to 14 V
    D19-10 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component without harness connected
    (to Air Conditioning Control Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK

REPLACE AIR CONDITIONING CONTROL ASSEMBLY (Click here)