Home › Engine / Hybrid System › FA20 STARTING › KEY INTER LOCK SYSTEM

KEY INTER LOCK SYSTEM > Key Cannot be Removed or Inserted

for Preparation Click here


DESCRIPTION

When an ACC signal and a P signal is input, the control unit relay assembly outputs a signal to the key inter lock solenoid.

WIRING DIAGRAM

Refer to System Diagram (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK WIRE HARNESS AND CONNECTOR (ACC VOLTAGE)


    A280136E01
  1. Disconnect the D42 control unit relay assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-6 (ACC) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to control unit relay assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK WIRE HARNESS AND CONNECTOR (CONTROL UNIT RELAY ASSEMBLY - BODY GROUND)
  1. Disconnect the D42 control unit relay assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D42-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT P SWITCH (FLOOR SHIFT SHIFT LEVER HOUSING)
  1. Inspect the P switch (floor shift shift lever housing) .



NG
REPLACE P SWITCH (FLOOR SHIFT SHIFT LEVER HOUSING) (Click here)
OK


4.CHECK WIRE HARNESS AND CONNECTOR (CONTROL UNIT RELAY ASSEMBLY - P SWITCH (FLOOR SHIFT SHIFT LEVER HOUSING)
  1. Disconnect the D42 control unit relay assembly connector.

  1. Disconnect the D28 P switch (floor shift shift lever housing) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D42-4 (P) - D28-1 (P)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D42-4 (P) or D28-1 (P) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK WIRE HARNESS AND CONNECTOR (P SWITCH (FLOOR SHIFT SHIFT LEVER HOUSING) - BODY GROUND)
  1. Disconnect the D28 P switch (floor shift shift lever housing) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D28-3 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK KEY INTER LOCK SOLENOID


    A280137E01
  1. Disconnect the D60 key inter lock solenoid connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    13.05 to 15.95 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Key Inter Lock Solenoid)



NG
REPLACE KEY INTER LOCK SOLENOID (Click here)
OK


7.CHECK WIRE HARNESS AND CONNECTOR (CONTROL UNIT RELAY ASSEMBLY - KEY INTER LOCK SOLENOID)
  1. Disconnect the D42 control unit relay assembly connector.

  1. Disconnect the D60 key inter lock solenoid connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D42-5 (KLS+) - D60-2
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D42-5 (KLS+) or D60-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK WIRE HARNESS AND CONNECTOR (KEY INTER LOCK SOLENOID - BODY GROUND)
  1. Disconnect the D60 key inter lock solenoid connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D60-1 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CONTROL UNIT RELAY ASSEMBLY (Click here)