Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)

ENTRY AND START SYSTEM (for Entry Function) > Driver Side Door Entry Unlock Function does not Operate

for Preparation Click here


DESCRIPTION

If the driver side door entry unlock function does not operate but the entry lock function operates, the communication between the vehicle and electrical key transmitter sub-assembly is normal. The malfunctioning part may be the unlock sensor circuit (from certification ECU (smart key ECU assembly) to the front door outside handle assembly (for driver side electrical key antenna)).

WIRING DIAGRAM


B312718E01


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
  2. The entry and start system (for Entry Function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication system is functioning properly.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (Click here).
  4. Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  5. After repair, confirm DTC does not reoccur by performing the "DTC Output Confirmation Operation".
  6. When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.

1.CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (PROCEED TO PROBLEM SYMPTOMS TABLE) (Click here)
OK


2.READ VALUE USING GTS (D-DOOR LOCK POS SW)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the GTS, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D-Door Lock Pos SW
    Driver side door unlock detection switch signal / LOCK or UNLOCK
    LOCK: Driver side door locked
    UNLOCK: Driver side door unlocked
    -

    OK:
    On the GTS screen, the display changes between ON and OFF as shown in the table above.



NG
GO TO LIGHTING SYSTEM (PROCEED TO DOOR UNLOCK DETECTION SWITCH CIRCUIT) (Click here)
OK


3.READ VALUE USING GTS (D-DOOR TOUCH SENSOR)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Entry & Start / Data List.

  1. According to the display on the GTS, read the Data List.

    Entry & Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D-Door Touch Sensor
    Front door outside handle assembly (for driver side) (lock sensor) / OFF or ON
    OFF: Front door outside handle assembly (for driver side) (unlock sensor) not touched
    ON: Front door outside handle assembly (for driver side) (unlock sensor) touched
    1. Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
    2. Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.

    OK:
    On the GTS screen, the display changes between ON and OFF as shown in the table above.



NG
Go to step 4
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY)
  1. Disconnect the D41and D48 certification ECU (smart key ECU assembly) connectors.

  1. Disconnect the E1*1 or F5*2 front door outside handle assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    D41-22 (SEN1) - E1-4 (SENS)
    Always
    Below 1 Ω
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω
    D41-22 (SEN1) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    D41-22 (SEN1) - F5-4 (SENS)
    Always
    Below 1 Ω
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω
    D41-22 (SEN1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE DOOR)
  1. Reconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

  1. Reconnect the E1*1 or F5*2 front door outside handle assembly (for driver side door) connector.

    1. *1: for LHD
    2. *2: for RHD



  1. Using an oscilloscope, check the waveform.


    B271432E02


    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (smart key ECU assembly))
    *b
    Waveform
    *c
    In actuality, sampling is being performed
    -
    -

    OK:

    Tester Connection
    Switch Condition
    Tool Setting
    Specified Condition
    D41-22 (SEN1) - D48-11 (GND)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors locked
    4. Electrical key transmitter sub-assembly not sufficiently close to vehicle
    5. Driver side door unlock sensor not touched → touched
    2 V/DIV., 500 ms/DIV
    Pulse generation
    (See waveform)



NG
REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE DOOR) (Click here)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)